Ge 489 User Manual Page 87
- Page / 259
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
GE Multilin 489 Generator Management Relay 4-37
4 SETPOINTS 4.7 S6 VOLTAGE ELEMENTS
4
4.7.5 UNDERFREQUENCY
PATH: SETPOINTS ÖØ S6 VOLTAGE ELEMENTS ÖØ UNDERFREQUENCY
It may be undesirable to enable the underfrequency elements until the generator is online. This feature can be blocked until
the generator is online and the block time expires. From that point forward, the underfrequency trip and alarm elements will
be active. A value of zero for the block time indicates that the underfrequency protection is active as soon as voltage
exceeds the cutoff level (programmed as a multiple of the generator rated phase-phase voltage). Frequency is then mea-
sured. Once the frequency of Vab is less than the underfrequency setpoints, for the period of time specified, a trip or alarm
will occur. There are dual level and time setpoints for the trip element.
UNDERFREQUENCY
[ENTER] for more
BLOCK UNDERFREQUENCY
FROM ONLINE: 1 s
Range: 0 to 5 s in steps of 1
VOLTAGE LEVEL
CUTOFF: 0.50 x Rated
Range: 0.50 to 0.99 × Rated in steps of 0.01
UNDERFREQUENCY
ALARM: Off
Range: Off, Latched, Unlatched
ASSIGN ALARM
RELAYS (2-5): ---5
Range: Any combination of Relays 2 to 5
UNDERFREQUENCY
ALARM LEVEL: 59.50 Hz
Range: 20.00 to 60.00 Hz in steps of 0.01
UNDERFREQUENCY
ALARM DELAY: 5.0 s
Range: 0.1 to 5000.0 s in steps of 0.1
UNDERFREQUENCY
ALARM EVENTS: Off
Range: On, Off
UNDERFREQUENCY
TRIP: Off
Range: Off, Latched, Unlatched
ASSIGN TRIP
RELAYS (1-4): 1---
Range: Any combination of Relays 1 to 4
UNDERFREQUENCY
TRIP LEVEL1: 59.50 Hz
Range: 20.00 to 60.00 Hz in steps of 0.01
UNDERFREQUENCY
TRIP DELAY1: 60.0 s
Range: 0.1 to 5000.0 s in steps of 0.1
UNDERFREQUENCY
TRIP LEVEL2: 58.00 Hz
Range: 20.00 to 60.00 Hz in steps of 0.01
UNDERFREQUENCY
TRIP DELAY2: 30.0 s
Range: 0.1 to 5000.0 s in steps of 0.1
ENTER
ESCAPE
ð
ð
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
- GENERATOR MANAGEMENT RELAY 1
- Instruction Manual 1
- 1. INTRODUCTION 1.1 OVERVIEW 3
- 4. SETPOINTS 4.1 OVERVIEW 3
- 5. ACTUAL VALUES 5.1 OVERVIEW 5
- 7. TESTING 7.1 TEST SETUP 6
- TABLE OF CONTENTS 8
- 27TN59GN 9
- ≥ 2 × CT: ±1% of 20 × CT 12
- LONG-TERM STORAGE 16
- 808704A1.CDR 19
- 2 INSTALLATION 2.1 MECHANICAL 21
- 2.1.5 TERMINAL LOCATIONS 21
- Figure 2–8: TERMINAL LAYOUT 21
- 2.1 MECHANICAL 2 INSTALLATION 22
- Table 2–1: 489 TERMINAL LIST 22
- 2 INSTALLATION 2.2 ELECTRICAL 23
- RTD SENSING 28
- GE Multilin 31
- 2.2 ELECTRICAL 2 INSTALLATION 32
- S3 DIGITAL INPUTS / 33
- SETPOINT 34
- NEW SETPOINT HAS BEEN 35
- 808745A1.CDR 37
- 808744A1.CDR 39
- 32 I 151 A8 .000 41
- 808726A2.CDR 45
- 808730A2.CDR 46
- VOLTAGE LEVEL 47
- CURRENT PHASOR 47
- VOLTAGE PHASOR 47
- CURRENT LEVEL 47
- EVENT SELECT BUTTONS 48
- EVENT LISTING 48
- VIEW DATA 48
- CLEAR EVENTS 48
- ACTIVATE SET 56
- (EQ 4.1) 62
- (EQ 4.2) 63
- S1 489 SETUP Ö 64
- Range: Breaker Auxiliary a 64
- Breaker Auxiliary b 64
- (EQ 4.8) 74
- 808731A1.CDR 75
- (EQ 4.9) 76
- CURRENT VOLTAGE 77
- (EQ 4.10) 78
- (EQ 4.11) 78
- I(multiples of CT) 81
- (multiples of CT) 81
- 808812A3.CDR 82
- (EQ 4.18) 83
- (EQ 4.19) 84
- TIME DELAY SETTING 85
- TO Vneutral OFEACH489 90
- AUXILIARY CONTACT 90
- TO DIGITAL INPUT FOR 90
- NEUTRAL O/V SUPERVISION 90
- GROUNDINGSWITCH 90
- (EQ 4.21) 91
- (EQ 4.22) 91
- (EQ 4.23) 92
- (EQ 4.24) 92
- 808740A1.CDR 94
- (EQ 4.25) 96
- 806827A1.CDR 105
- (EQ 4.26) 107
- (EQ 4.27) 107
- MULTIPLE OF FULL LOAD AMPS 108
- TIME IN SECONDS 108
- (EQ 4.28) 109
- TIME TO TRIP IN SECONDS 110
- THERMAL LIMITS 111
- FOR HIGH INERTIAL LOAD 111
- VOLTAGE DEPENDENT OVERLOAD 112
- (CUSTOM CURVE) 112
- VOLTAGE DEPENDENT 113
- OVERLOAD PROTECTION CURVES 113
- OVERLOAD PROTECTION at 80% V 114
- NEMA GE MULTILIN 115
- Thermal Capacity Used 116
- MOTOR TRIPPED 116
- 100% LOAD 116
- MOTOR STOPPED 116
- 80% LOAD 116
- 808721A1.CDR 118
- Range: On, Off 120
- (EQ 4.37) 123
- (EQ 4.38) 123
- 808738A1.CDR 124
- THIS FEATURE NOT PROGRAMMED 149
- THIS FEA 149
- TURE NOT PROGRAMMED 149
- THIS FEATURE NOT PRO 150
- LAST TRIP DATA: 158
- ACTIVE ALARMS: 158
- START BLOCK 158
- LOCKOUTS: 158
- 6.3.7 489 MEMORY MAP 172
- 6.3.8 MEMORY MAP DATA FORMATS 196
- No Counters Reported 202
- Configurable 202
- 7.1 TEST SETUP 7 TESTING 214
- A2 METERING DATA 218
- TEMPERATURE 218
- 3 PHASE VARIABLE AC TEST SET 224
- (EQ 7.5) 226
- (EQ 7.6) 226
- (EQ 7.7) 226
- 808739A1.CDR 229
- 808736A1.CDR 231
- 808735A1.CDR 231
- 808734A1.CDR 232
- (EQ A.1) 233
- (EQ A.2) 233
- HGF3/HGF5 234
- DIMENSIONS 234
- 808712A1.CDR 236
- 489 ANSI 237
- MODERATELY INVERSE 237
- NORMALLY INVERSE 238
- VERY INVERSE 239
- CURRENT (I/Ipu) 240
- TRIPTIME (sec) 240
- DEFINITE TIME 241
- SHORT INVERSE 242
- IAC INVERSE 243
- EXTREME INVERSE 245
- IEC CURVE A (BS142) 246
- IEC CURVE B (BS142) 247
- IEC CURVE C (BS142) 248
- GE Multilin Relay Warranty 251
- Numerics 253
Related products and manuals for Generators Ge 489
Generators Ge GEH-5304A User Manual
(45 pages)
(45 pages)
Generators Ge A-6451 User Manual
(32 pages)
(32 pages)
Generators Ge A4021 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals