Ge 489 User Manual Page 156
- Page / 259
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-24 489 Generator Management Relay GE Multilin
5.6 A5 EVENT RECORDER 5 ACTUAL VALUES
5
The 489 Event Recorder stores generator and system information each time an event occurs. The description of the event
is stored and a time and date stamp is also added to the record. This allows reconstruction of the sequence of events for
troubleshooting. Events include: all trips, any alarm optionally (except Service Alarm, and 489 Not Inserted Alarm, which
always records as events), loss of control power, application of control power, thermal resets, simulation, serial communica-
tion starts/stops and general input control functions optionally.
EVENT01 is the most recent event and EVENT40 is the oldest event. Each new event bumps the other event records down
until the 40th event is reached. The 40th event record is lost when the next event occurs. This information can be cleared
using S1 489 SETUP ÖØ CLEAR DATA ÖØ CLEAR EVENT RECORD setpoint. The event record will not update if a digital input
programmed as Test Input is shorted.
ANALOG INPUT 2
EVENT01: 0.0 Units
Range: –50000 to 50000
Seen only if the Analog Input is in use.
ANALOG INPUT 3
EVENT01: 0.0 Units
Range: –50000 to 50000
Seen only if the Analog Input is in use.
ANALOG INPUT 4
EVENT01: 0.0 Units
Range: –50000 to 50000
Seen only if the Analog Input is in use.
Table 5–1: CAUSE OF EVENTS
TRIPS
Ambient RTD12 Trip * Analog I/P 1 to 4 Trip * Bearing RTD 7 Trip * Bearing RTD 8 Trip *
Bearing RTD 9 Trip * Bearing RTD 10 Trip * Differential Trip Distance Zone 1 Trip
Distance Zone 2 Trip Field-Bkr Discr. Trip Gnd Directional Trip Ground O/C Trip
Hiset Phase O/C Trip Input A to G Trip * Loss of Excitation 1 Loss of Excitation 2
Low Fwd Power Trip Neg Seq O/C Trip Neutral O/V Trip Neut. U/V (3rd) Trip
Offline O/C Trip Overfrequency Trip Overvoltage Trip Phase O/C Trip
Phase Reversal Trip Reactive Power Trip Reverse Power Trip RTD11 Trip *
Sequential Trip Stator RTD 1 Trip * Stator RTD 2 Trip * Stator RTD 3 Trip *
Stator RTD 4 Trip * Stator RTD 5 Trip * Stator RTD 6 Trip * Tachometer Trip
Thermal Model Trip Underfrequency Trip Undervoltage Trip Volts/Hertz Trip
ALARMS (OPTIONAL EVENTS)
Ambient RTD12 Alarm * Analog I/P 1 to 4 Alarm * Bearing RTD 7 Alarm * Bearing RTD 8 Alarm *
Bearing RTD 9 Alarm * Bearing RTD 10 Alarm * Breaker Failure Current Demand Alarm
Gnd Directional Alarm Ground O/C Alarm Input A to G Alarm * Low Fwd Power Alarm
MVA Alarm Mvar Alarm MW Alarm NegSeq Current Alarm
Neut. U/V 3rd Alarm Neutral O/V Alarm Open RTD Alarm Overcurrent Alarm
Overfrequency Alarm Overvoltage Alarm Reactive Power Alarm Reverse Power Alarm
RTD11 Alarm * Short/Low RTD Alarm Stator RTD 1 Alarm Stator RTD 2 Alarm
Stator RTD 3 Alarm Stator RTD 4 Alarm Stator RTD 5 Alarm Stator RTD 6 Alarm
Tachometer Alarm Thermal Model Alarm Trip Coil Monitor Trip Counter Alarm
Underfrequency Alarm Undervoltage Alarm VT Fuse Fail Alarm
OTHER
489 Not Inserted Control Power Applied Control Power Lost Dig I/P Waveform Trig
Input A to G Control * IRIG-B Failure Serial Comm. Start Serial Comm. Stop
Serial Waveform Trip Setpoint 1 Active Setpoint 2 Active Simulation Started
Simulation Stopped Thermal Reset Close Thermal Reset Open
* reflects the name that is programmed
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
- GENERATOR MANAGEMENT RELAY 1
- Instruction Manual 1
- 1. INTRODUCTION 1.1 OVERVIEW 3
- 4. SETPOINTS 4.1 OVERVIEW 3
- 5. ACTUAL VALUES 5.1 OVERVIEW 5
- 7. TESTING 7.1 TEST SETUP 6
- TABLE OF CONTENTS 8
- 27TN59GN 9
- ≥ 2 × CT: ±1% of 20 × CT 12
- LONG-TERM STORAGE 16
- 808704A1.CDR 19
- 2 INSTALLATION 2.1 MECHANICAL 21
- 2.1.5 TERMINAL LOCATIONS 21
- Figure 2–8: TERMINAL LAYOUT 21
- 2.1 MECHANICAL 2 INSTALLATION 22
- Table 2–1: 489 TERMINAL LIST 22
- 2 INSTALLATION 2.2 ELECTRICAL 23
- RTD SENSING 28
- GE Multilin 31
- 2.2 ELECTRICAL 2 INSTALLATION 32
- S3 DIGITAL INPUTS / 33
- SETPOINT 34
- NEW SETPOINT HAS BEEN 35
- 808745A1.CDR 37
- 808744A1.CDR 39
- 32 I 151 A8 .000 41
- 808726A2.CDR 45
- 808730A2.CDR 46
- VOLTAGE LEVEL 47
- CURRENT PHASOR 47
- VOLTAGE PHASOR 47
- CURRENT LEVEL 47
- EVENT SELECT BUTTONS 48
- EVENT LISTING 48
- VIEW DATA 48
- CLEAR EVENTS 48
- ACTIVATE SET 56
- (EQ 4.1) 62
- (EQ 4.2) 63
- S1 489 SETUP Ö 64
- Range: Breaker Auxiliary a 64
- Breaker Auxiliary b 64
- (EQ 4.8) 74
- 808731A1.CDR 75
- (EQ 4.9) 76
- CURRENT VOLTAGE 77
- (EQ 4.10) 78
- (EQ 4.11) 78
- I(multiples of CT) 81
- (multiples of CT) 81
- 808812A3.CDR 82
- (EQ 4.18) 83
- (EQ 4.19) 84
- TIME DELAY SETTING 85
- TO Vneutral OFEACH489 90
- AUXILIARY CONTACT 90
- TO DIGITAL INPUT FOR 90
- NEUTRAL O/V SUPERVISION 90
- GROUNDINGSWITCH 90
- (EQ 4.21) 91
- (EQ 4.22) 91
- (EQ 4.23) 92
- (EQ 4.24) 92
- 808740A1.CDR 94
- (EQ 4.25) 96
- 806827A1.CDR 105
- (EQ 4.26) 107
- (EQ 4.27) 107
- MULTIPLE OF FULL LOAD AMPS 108
- TIME IN SECONDS 108
- (EQ 4.28) 109
- TIME TO TRIP IN SECONDS 110
- THERMAL LIMITS 111
- FOR HIGH INERTIAL LOAD 111
- VOLTAGE DEPENDENT OVERLOAD 112
- (CUSTOM CURVE) 112
- VOLTAGE DEPENDENT 113
- OVERLOAD PROTECTION CURVES 113
- OVERLOAD PROTECTION at 80% V 114
- NEMA GE MULTILIN 115
- Thermal Capacity Used 116
- MOTOR TRIPPED 116
- 100% LOAD 116
- MOTOR STOPPED 116
- 80% LOAD 116
- 808721A1.CDR 118
- Range: On, Off 120
- (EQ 4.37) 123
- (EQ 4.38) 123
- 808738A1.CDR 124
- THIS FEATURE NOT PROGRAMMED 149
- THIS FEA 149
- TURE NOT PROGRAMMED 149
- THIS FEATURE NOT PRO 150
- LAST TRIP DATA: 158
- ACTIVE ALARMS: 158
- START BLOCK 158
- LOCKOUTS: 158
- 6.3.7 489 MEMORY MAP 172
- 6.3.8 MEMORY MAP DATA FORMATS 196
- No Counters Reported 202
- Configurable 202
- 7.1 TEST SETUP 7 TESTING 214
- A2 METERING DATA 218
- TEMPERATURE 218
- 3 PHASE VARIABLE AC TEST SET 224
- (EQ 7.5) 226
- (EQ 7.6) 226
- (EQ 7.7) 226
- 808739A1.CDR 229
- 808736A1.CDR 231
- 808735A1.CDR 231
- 808734A1.CDR 232
- (EQ A.1) 233
- (EQ A.2) 233
- HGF3/HGF5 234
- DIMENSIONS 234
- 808712A1.CDR 236
- 489 ANSI 237
- MODERATELY INVERSE 237
- NORMALLY INVERSE 238
- VERY INVERSE 239
- CURRENT (I/Ipu) 240
- TRIPTIME (sec) 240
- DEFINITE TIME 241
- SHORT INVERSE 242
- IAC INVERSE 243
- EXTREME INVERSE 245
- IEC CURVE A (BS142) 246
- IEC CURVE B (BS142) 247
- IEC CURVE C (BS142) 248
- GE Multilin Relay Warranty 251
- Numerics 253
Related products and manuals for Generators Ge 489
Generators Ge GEH-5304A User Manual
(45 pages)
(45 pages)
Generators Ge A-6451 User Manual
(32 pages)
(32 pages)
Generators Ge A4021 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.177 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals