Ge 489 User Manual Page 146
- Page / 259
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-14 489 Generator Management Relay GE Multilin
5.3 A2 METERING DATA 5 ACTUAL VALUES
5
5.3.2 VOLTAGE METERING
PATH: ACTUAL VALUES ÖØ A2 METERING DATA ÖØ VOLTAGE METERING
Measured voltage parameters will be displayed here. The V/Hz measurement is a per unit value based on Vab voltage/
measured frequency divided by VT nominal/nominal system frequency. Polar coordinates for measured phase and/or line
voltages are also shown using Va (wye connection) or Vab (open delta connection) as a zero angle reference vector. In the
absence of a voltage signal (Va or Vab), IA output current is used as the zero angle reference vector.
If
VT CONNECTION TYPE is programmed as "None" and NEUTRAL VOLTAGE TRANSFORMER is "No" in S2 SYSTEM, the follow-
ing flash message will appear when an attempt is made to enter this group of messages.
VOLTAGE METERING
[ENTER] for more
Vab: 0 Vbc: 0
Vca: 0 Volts
Range: 0 to 50000 V. Not seen if VT CONNECTION is
programmed as None.
AVERAGE LINE
VOLTAGE: 0 Volts
Range: 0 to 50000 V. Not seen if VT CONNECTION is
programmed as None.
Van: 0 Vbn: 0
Vcn: 0 Volts
Range: 0 to 50000 V. Seen only if VT CONNECTION is
programmed as Wye.
AVERAGE PHASE
VOLTAGE: 0 Volts
Range: 0 to 50000 V. Seen only if VT CONNECTION is
programmed as Wye.
LINE A-B VOLTAGE:
0 V 0° Lag
Range: 0 to 50000 V, 0 to 359°. Not seen if VT
CONNECTION is programmed as None.
LINE B-C VOLTAGE:
0 V 0° Lag
Range: 0 to 50000 V, 0 to 359°. Not seen if VT
CONNECTION is programmed as None.
LINE C-A VOLTAGE:
0 V 0° Lag
Range: 0 to 50000 V, 0 to 359°. Not seen if VT
CONNECTION is programmed as None.
PHASE A-N VOLTAGE:
0 V 0° Lag
Range: 0 to 50000 V, 0 to 359°. Seen only if VT
CONNECTION is programmed as Wye.
PHASE B-N VOLTAGE:
0 V 0° Lag
Range: 0 to 50000 V, 0 to 359°. Seen only if VT
CONNECTION is programmed as Wye.
PHASE C-N VOLTAGE:
0 V 0° Lag
Range: 0 to 50000 V, 0 to 359°. Seen only if VT
CONNECTION is programmed as Wye.
PER UNIT MEASUREMENT
OF V/Hz: 0.00
Range: 0.00 to 2.00. Not seen if VT CONNECTION is
programmed as None.
FREQUENCY:
0.00 Hz
Range: 0.00 to 90.00 Hz. Not seen if VT CONNECTION
is programmed as None.
NEUTRAL VOLTAGE
FUND: 0.0 V
Range: 0.0 to 25000.0 V. Seen only if there is a neutral
voltage transformer.
NEUTRAL VOLTAGE
3rd HARM: 0.0 V
Range: 0.0 to 25000.0 V. Seen only if there is a neutral
voltage transformer.
TERMINAL VOLTAGE
3rd HARM: 0.0 V
Range: 0.0 to 25000.0 V. Seen only if VT CONNECTION
is programmed as Wye.
IMPEDANCE Vab / Iab
0.0 Ω sec. 0°
Range: 0.0 to 6553.5 Ωsec., 0 to 359°
THIS FEATURE
NOT PROGRAMMED
ENTER
ESCAPE
ð
ð
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
- GENERATOR MANAGEMENT RELAY 1
- Instruction Manual 1
- 1. INTRODUCTION 1.1 OVERVIEW 3
- 4. SETPOINTS 4.1 OVERVIEW 3
- 5. ACTUAL VALUES 5.1 OVERVIEW 5
- 7. TESTING 7.1 TEST SETUP 6
- TABLE OF CONTENTS 8
- 27TN59GN 9
- ≥ 2 × CT: ±1% of 20 × CT 12
- LONG-TERM STORAGE 16
- 808704A1.CDR 19
- 2 INSTALLATION 2.1 MECHANICAL 21
- 2.1.5 TERMINAL LOCATIONS 21
- Figure 2–8: TERMINAL LAYOUT 21
- 2.1 MECHANICAL 2 INSTALLATION 22
- Table 2–1: 489 TERMINAL LIST 22
- 2 INSTALLATION 2.2 ELECTRICAL 23
- RTD SENSING 28
- GE Multilin 31
- 2.2 ELECTRICAL 2 INSTALLATION 32
- S3 DIGITAL INPUTS / 33
- SETPOINT 34
- NEW SETPOINT HAS BEEN 35
- 808745A1.CDR 37
- 808744A1.CDR 39
- 32 I 151 A8 .000 41
- 808726A2.CDR 45
- 808730A2.CDR 46
- VOLTAGE LEVEL 47
- CURRENT PHASOR 47
- VOLTAGE PHASOR 47
- CURRENT LEVEL 47
- EVENT SELECT BUTTONS 48
- EVENT LISTING 48
- VIEW DATA 48
- CLEAR EVENTS 48
- ACTIVATE SET 56
- (EQ 4.1) 62
- (EQ 4.2) 63
- S1 489 SETUP Ö 64
- Range: Breaker Auxiliary a 64
- Breaker Auxiliary b 64
- (EQ 4.8) 74
- 808731A1.CDR 75
- (EQ 4.9) 76
- CURRENT VOLTAGE 77
- (EQ 4.10) 78
- (EQ 4.11) 78
- I(multiples of CT) 81
- (multiples of CT) 81
- 808812A3.CDR 82
- (EQ 4.18) 83
- (EQ 4.19) 84
- TIME DELAY SETTING 85
- TO Vneutral OFEACH489 90
- AUXILIARY CONTACT 90
- TO DIGITAL INPUT FOR 90
- NEUTRAL O/V SUPERVISION 90
- GROUNDINGSWITCH 90
- (EQ 4.21) 91
- (EQ 4.22) 91
- (EQ 4.23) 92
- (EQ 4.24) 92
- 808740A1.CDR 94
- (EQ 4.25) 96
- 806827A1.CDR 105
- (EQ 4.26) 107
- (EQ 4.27) 107
- MULTIPLE OF FULL LOAD AMPS 108
- TIME IN SECONDS 108
- (EQ 4.28) 109
- TIME TO TRIP IN SECONDS 110
- THERMAL LIMITS 111
- FOR HIGH INERTIAL LOAD 111
- VOLTAGE DEPENDENT OVERLOAD 112
- (CUSTOM CURVE) 112
- VOLTAGE DEPENDENT 113
- OVERLOAD PROTECTION CURVES 113
- OVERLOAD PROTECTION at 80% V 114
- NEMA GE MULTILIN 115
- Thermal Capacity Used 116
- MOTOR TRIPPED 116
- 100% LOAD 116
- MOTOR STOPPED 116
- 80% LOAD 116
- 808721A1.CDR 118
- Range: On, Off 120
- (EQ 4.37) 123
- (EQ 4.38) 123
- 808738A1.CDR 124
- THIS FEATURE NOT PROGRAMMED 149
- THIS FEA 149
- TURE NOT PROGRAMMED 149
- THIS FEATURE NOT PRO 150
- LAST TRIP DATA: 158
- ACTIVE ALARMS: 158
- START BLOCK 158
- LOCKOUTS: 158
- 6.3.7 489 MEMORY MAP 172
- 6.3.8 MEMORY MAP DATA FORMATS 196
- No Counters Reported 202
- Configurable 202
- 7.1 TEST SETUP 7 TESTING 214
- A2 METERING DATA 218
- TEMPERATURE 218
- 3 PHASE VARIABLE AC TEST SET 224
- (EQ 7.5) 226
- (EQ 7.6) 226
- (EQ 7.7) 226
- 808739A1.CDR 229
- 808736A1.CDR 231
- 808735A1.CDR 231
- 808734A1.CDR 232
- (EQ A.1) 233
- (EQ A.2) 233
- HGF3/HGF5 234
- DIMENSIONS 234
- 808712A1.CDR 236
- 489 ANSI 237
- MODERATELY INVERSE 237
- NORMALLY INVERSE 238
- VERY INVERSE 239
- CURRENT (I/Ipu) 240
- TRIPTIME (sec) 240
- DEFINITE TIME 241
- SHORT INVERSE 242
- IAC INVERSE 243
- EXTREME INVERSE 245
- IEC CURVE A (BS142) 246
- IEC CURVE B (BS142) 247
- IEC CURVE C (BS142) 248
- GE Multilin Relay Warranty 251
- Numerics 253
Related products and manuals for Generators Ge 489
Generators Ge GEH-5304A User Manual
(45 pages)
(45 pages)
Generators Ge A-6451 User Manual
(32 pages)
(32 pages)
Generators Ge A4021 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.258 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals