Ge 489 User Manual Page 120
- Page / 259
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-70 489 Generator Management Relay GE Multilin
4.11 S10 MONITORING 4 SETPOINTS
4
4.11.3 TRIP COIL MONITOR
PATH: SETPOINTS ÖØ S10 MONITORING ÖØ TRIP COIL MONITOR
If the trip coil monitor alarm feature is enabled as latched or unlatched, the trip coil supervision circuitry will monitor the trip
coil circuit for continuity any time that the breaker status input indicates that the breaker is closed. If that continuity is bro-
ken, a trip coil monitor alarm will occur in approximately 300 ms.
If 52 Open/Closed is selected, the trip coil supervision circuitry monitors the trip coil circuit for continuity at all times regard-
less of breaker state. This requires an alternate path around the 52a contacts in series with the trip coil when the breaker is
open. See the figure below for modifications to the wiring and proper resistor selection. If that continuity is broken, a Starter
Failure alarm will indicate Trip Coil Supervision.
Figure 4–19: TRIP COIL SUPERVISION
TRIP COIL MONITOR
[ENTER] for more
TRIP COIL MONITOR
ALARM: Off
Range: Off, Latched, Unlatched
ASSIGN ALARM
RELAYS (2-5): ---5
Range: Any combination of Relays 2 to 5
SUPERVISION OF TRIP
COIL: 52 Closed
Range: 52 Closed, 52 Open/Closed
TRIP COIL MONITOR
ALARM EVENTS: Off
Range: On, Off
ENTER
ESCAPE
ð
ð
MESSAGE
ESCAPE
MESSAGE
ESCAPE
MESSAGE
ESCAPE
808727A1.CDR
VALUE OF RESISTOR 'R'
SUPPLY
OHMS
WATTS
48 VDC
125 VDC
250 VDC
10 K
25 K
50 K
2
5
5
TRIP
COIL
TRIPCOIL
SUPERVISION
R1 TRIP
CONTACT
F11
E2
F1
E11
52a
TRIP COIL CLOSED SUPERVISION
"52 Closed"
TRIPCOIL
SUPERVISION
R1 TRIP
CONTACT
TRIP
COIL
F11
E2
F1
E11
52a
TRIP COIL OPEN/CLOSED SUPERVISION
"52 Open/Closed"
52a
TRIP
COIL
TRIPCOIL
SUPERVISION
R1 TRIP
CONTACT
F11
E2
F1
E11
52a
TRIP COIL
OPEN/CLOSED
SUPERVISION
"52 Open/Closed"
WITH MULTIPLE
BREAKER AUX
CONTACTS
- GENERATOR MANAGEMENT RELAY 1
- Instruction Manual 1
- 1. INTRODUCTION 1.1 OVERVIEW 3
- 4. SETPOINTS 4.1 OVERVIEW 3
- 5. ACTUAL VALUES 5.1 OVERVIEW 5
- 7. TESTING 7.1 TEST SETUP 6
- TABLE OF CONTENTS 8
- 27TN59GN 9
- ≥ 2 × CT: ±1% of 20 × CT 12
- LONG-TERM STORAGE 16
- 808704A1.CDR 19
- 2 INSTALLATION 2.1 MECHANICAL 21
- 2.1.5 TERMINAL LOCATIONS 21
- Figure 2–8: TERMINAL LAYOUT 21
- 2.1 MECHANICAL 2 INSTALLATION 22
- Table 2–1: 489 TERMINAL LIST 22
- 2 INSTALLATION 2.2 ELECTRICAL 23
- RTD SENSING 28
- GE Multilin 31
- 2.2 ELECTRICAL 2 INSTALLATION 32
- S3 DIGITAL INPUTS / 33
- SETPOINT 34
- NEW SETPOINT HAS BEEN 35
- 808745A1.CDR 37
- 808744A1.CDR 39
- 32 I 151 A8 .000 41
- 808726A2.CDR 45
- 808730A2.CDR 46
- VOLTAGE LEVEL 47
- CURRENT PHASOR 47
- VOLTAGE PHASOR 47
- CURRENT LEVEL 47
- EVENT SELECT BUTTONS 48
- EVENT LISTING 48
- VIEW DATA 48
- CLEAR EVENTS 48
- ACTIVATE SET 56
- (EQ 4.1) 62
- (EQ 4.2) 63
- S1 489 SETUP Ö 64
- Range: Breaker Auxiliary a 64
- Breaker Auxiliary b 64
- (EQ 4.8) 74
- 808731A1.CDR 75
- (EQ 4.9) 76
- CURRENT VOLTAGE 77
- (EQ 4.10) 78
- (EQ 4.11) 78
- I(multiples of CT) 81
- (multiples of CT) 81
- 808812A3.CDR 82
- (EQ 4.18) 83
- (EQ 4.19) 84
- TIME DELAY SETTING 85
- TO Vneutral OFEACH489 90
- AUXILIARY CONTACT 90
- TO DIGITAL INPUT FOR 90
- NEUTRAL O/V SUPERVISION 90
- GROUNDINGSWITCH 90
- (EQ 4.21) 91
- (EQ 4.22) 91
- (EQ 4.23) 92
- (EQ 4.24) 92
- 808740A1.CDR 94
- (EQ 4.25) 96
- 806827A1.CDR 105
- (EQ 4.26) 107
- (EQ 4.27) 107
- MULTIPLE OF FULL LOAD AMPS 108
- TIME IN SECONDS 108
- (EQ 4.28) 109
- TIME TO TRIP IN SECONDS 110
- THERMAL LIMITS 111
- FOR HIGH INERTIAL LOAD 111
- VOLTAGE DEPENDENT OVERLOAD 112
- (CUSTOM CURVE) 112
- VOLTAGE DEPENDENT 113
- OVERLOAD PROTECTION CURVES 113
- OVERLOAD PROTECTION at 80% V 114
- NEMA GE MULTILIN 115
- Thermal Capacity Used 116
- MOTOR TRIPPED 116
- 100% LOAD 116
- MOTOR STOPPED 116
- 80% LOAD 116
- 808721A1.CDR 118
- Range: On, Off 120
- (EQ 4.37) 123
- (EQ 4.38) 123
- 808738A1.CDR 124
- THIS FEATURE NOT PROGRAMMED 149
- THIS FEA 149
- TURE NOT PROGRAMMED 149
- THIS FEATURE NOT PRO 150
- LAST TRIP DATA: 158
- ACTIVE ALARMS: 158
- START BLOCK 158
- LOCKOUTS: 158
- 6.3.7 489 MEMORY MAP 172
- 6.3.8 MEMORY MAP DATA FORMATS 196
- No Counters Reported 202
- Configurable 202
- 7.1 TEST SETUP 7 TESTING 214
- A2 METERING DATA 218
- TEMPERATURE 218
- 3 PHASE VARIABLE AC TEST SET 224
- (EQ 7.5) 226
- (EQ 7.6) 226
- (EQ 7.7) 226
- 808739A1.CDR 229
- 808736A1.CDR 231
- 808735A1.CDR 231
- 808734A1.CDR 232
- (EQ A.1) 233
- (EQ A.2) 233
- HGF3/HGF5 234
- DIMENSIONS 234
- 808712A1.CDR 236
- 489 ANSI 237
- MODERATELY INVERSE 237
- NORMALLY INVERSE 238
- VERY INVERSE 239
- CURRENT (I/Ipu) 240
- TRIPTIME (sec) 240
- DEFINITE TIME 241
- SHORT INVERSE 242
- IAC INVERSE 243
- EXTREME INVERSE 245
- IEC CURVE A (BS142) 246
- IEC CURVE B (BS142) 247
- IEC CURVE C (BS142) 248
- GE Multilin Relay Warranty 251
- Numerics 253
Related products and manuals for Generators Ge 489
Generators Ge GEH-5304A User Manual
(45 pages)
(45 pages)
Generators Ge A-6451 User Manual
(32 pages)
(32 pages)
Generators Ge A4021 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.834 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals