Ge 489 User Manual Page 69
- Page / 259
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
GE Multilin 489 Generator Management Relay 4-19
4 SETPOINTS 4.4 S3 DIGITAL INPUTS
4
One of assignable digital inputs 4 to 7 may be assigned to the tachometer function to measure mechanical speed. The time
between each input closure is measured and converted to an RPM value based on one closure per revolution. If an over-
speed trip or alarm is enabled, and the measured RPM exceeds the threshold setpoint for the time specified by the delay, a
trip or alarm will occur. The RPM value can be viewed with the
A2 METERING DATA ÖØ SPEED ÖØ TACHOMETER actual
value.
For example, an inductive proximity probe or hall effect gear tooth sensor may be used to sense the key on the generator.
The probe could be powered from the +24V from the digital input power supply. The NPN transistor output could be taken
to one of the assignable digital inputs assigned to the tachometer function.
4.4.11 WAVEFORM CAPTURE
PATH: SETPOINTS ÖØ S3 DIGITAL INPUTS ÖØ WAVEFORM CAPTURE
This feature may be used to trigger the waveform capture from an external contact. When one of the inputs is assigned to
the Waveform Capture function, shorting that input will trigger the waveform.
4.4.12 GROUND SWITCH STATUS
PATH: SETPOINTS ÖØ S3 DIGITAL INPUTS ÖØ GND SWITCH STATUS
This function is used to detect the status of a grounding switch for the generator for which the relay is installed. Refer to
Appendix B for Application Notes.
WAVEFORM CAPTURE
[ENTER] for more
ASSIGN DIGITAL
INPUT: None
Range: None, Input 1 to Input 7. If an input is assigned to
the Tachometer, it may not be used here.
GND SWITCH STATUS
[ENTER] for more
ASSIGN DIGITAL
INPUT: None
Range: None, Input 1 to Input 7. If an input is assigned to
the Tachometer, it may not be used here.
GROUND SWITCH
CONTACT: Auxiliary a
Range: Auxiliary a, Auxiliary b
ENTER
ESCAPE
ð
ð
ENTER
ESCAPE
ð
ð
MESSAGE
ESCAPE
- GENERATOR MANAGEMENT RELAY 1
- Instruction Manual 1
- 1. INTRODUCTION 1.1 OVERVIEW 3
- 4. SETPOINTS 4.1 OVERVIEW 3
- 5. ACTUAL VALUES 5.1 OVERVIEW 5
- 7. TESTING 7.1 TEST SETUP 6
- TABLE OF CONTENTS 8
- 27TN59GN 9
- ≥ 2 × CT: ±1% of 20 × CT 12
- LONG-TERM STORAGE 16
- 808704A1.CDR 19
- 2 INSTALLATION 2.1 MECHANICAL 21
- 2.1.5 TERMINAL LOCATIONS 21
- Figure 2–8: TERMINAL LAYOUT 21
- 2.1 MECHANICAL 2 INSTALLATION 22
- Table 2–1: 489 TERMINAL LIST 22
- 2 INSTALLATION 2.2 ELECTRICAL 23
- RTD SENSING 28
- GE Multilin 31
- 2.2 ELECTRICAL 2 INSTALLATION 32
- S3 DIGITAL INPUTS / 33
- SETPOINT 34
- NEW SETPOINT HAS BEEN 35
- 808745A1.CDR 37
- 808744A1.CDR 39
- 32 I 151 A8 .000 41
- 808726A2.CDR 45
- 808730A2.CDR 46
- VOLTAGE LEVEL 47
- CURRENT PHASOR 47
- VOLTAGE PHASOR 47
- CURRENT LEVEL 47
- EVENT SELECT BUTTONS 48
- EVENT LISTING 48
- VIEW DATA 48
- CLEAR EVENTS 48
- ACTIVATE SET 56
- (EQ 4.1) 62
- (EQ 4.2) 63
- S1 489 SETUP Ö 64
- Range: Breaker Auxiliary a 64
- Breaker Auxiliary b 64
- (EQ 4.8) 74
- 808731A1.CDR 75
- (EQ 4.9) 76
- CURRENT VOLTAGE 77
- (EQ 4.10) 78
- (EQ 4.11) 78
- I(multiples of CT) 81
- (multiples of CT) 81
- 808812A3.CDR 82
- (EQ 4.18) 83
- (EQ 4.19) 84
- TIME DELAY SETTING 85
- TO Vneutral OFEACH489 90
- AUXILIARY CONTACT 90
- TO DIGITAL INPUT FOR 90
- NEUTRAL O/V SUPERVISION 90
- GROUNDINGSWITCH 90
- (EQ 4.21) 91
- (EQ 4.22) 91
- (EQ 4.23) 92
- (EQ 4.24) 92
- 808740A1.CDR 94
- (EQ 4.25) 96
- 806827A1.CDR 105
- (EQ 4.26) 107
- (EQ 4.27) 107
- MULTIPLE OF FULL LOAD AMPS 108
- TIME IN SECONDS 108
- (EQ 4.28) 109
- TIME TO TRIP IN SECONDS 110
- THERMAL LIMITS 111
- FOR HIGH INERTIAL LOAD 111
- VOLTAGE DEPENDENT OVERLOAD 112
- (CUSTOM CURVE) 112
- VOLTAGE DEPENDENT 113
- OVERLOAD PROTECTION CURVES 113
- OVERLOAD PROTECTION at 80% V 114
- NEMA GE MULTILIN 115
- Thermal Capacity Used 116
- MOTOR TRIPPED 116
- 100% LOAD 116
- MOTOR STOPPED 116
- 80% LOAD 116
- 808721A1.CDR 118
- Range: On, Off 120
- (EQ 4.37) 123
- (EQ 4.38) 123
- 808738A1.CDR 124
- THIS FEATURE NOT PROGRAMMED 149
- THIS FEA 149
- TURE NOT PROGRAMMED 149
- THIS FEATURE NOT PRO 150
- LAST TRIP DATA: 158
- ACTIVE ALARMS: 158
- START BLOCK 158
- LOCKOUTS: 158
- 6.3.7 489 MEMORY MAP 172
- 6.3.8 MEMORY MAP DATA FORMATS 196
- No Counters Reported 202
- Configurable 202
- 7.1 TEST SETUP 7 TESTING 214
- A2 METERING DATA 218
- TEMPERATURE 218
- 3 PHASE VARIABLE AC TEST SET 224
- (EQ 7.5) 226
- (EQ 7.6) 226
- (EQ 7.7) 226
- 808739A1.CDR 229
- 808736A1.CDR 231
- 808735A1.CDR 231
- 808734A1.CDR 232
- (EQ A.1) 233
- (EQ A.2) 233
- HGF3/HGF5 234
- DIMENSIONS 234
- 808712A1.CDR 236
- 489 ANSI 237
- MODERATELY INVERSE 237
- NORMALLY INVERSE 238
- VERY INVERSE 239
- CURRENT (I/Ipu) 240
- TRIPTIME (sec) 240
- DEFINITE TIME 241
- SHORT INVERSE 242
- IAC INVERSE 243
- EXTREME INVERSE 245
- IEC CURVE A (BS142) 246
- IEC CURVE B (BS142) 247
- IEC CURVE C (BS142) 248
- GE Multilin Relay Warranty 251
- Numerics 253
Related products and manuals for Generators Ge 489
Generators Ge GEH-5304A User Manual
(45 pages)
(45 pages)
Generators Ge A-6451 User Manual
(32 pages)
(32 pages)
Generators Ge A4021 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.516 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals