Ge 60-883-95R User Manual Page 29
- Page / 34
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
System Monitoring 24
Replacing the Backup Battery
¾ To replace the backup battery:
1. Turn the ON/OFF switch on the back of the panel to OFF.
2. Remove the panel cover by lifting on the tab at the top of the panel.
3. Loosen the speak screws. This makes removing the battery easier.
4. Remove the battery cover screw and cover. (See Figure 3)
Figure 5. Replacing the backup battery
Note
Lifting the panel and tilting it
toward yourself should aid in
the removal of the battery.
5. Remove the old battery.
6. Disconnect the cables from the old battery and connect them to the new one.
7. Install the new battery, positioning it under the edge of the speaker.
8. Carefully place the connecting wires above the speaker.
9. Tighten the speaker screws.
10. Replace the battery cover.
11. Replace and tighten the cover screw.
12. Replace the panel cover.
Sensor Low Battery
¾ If the panel gets a low battery message from a sensor, the following occurs:
Note
If Status is pressed during a
sensor low battery, the sys-
tem announces “Time is
x:xx, sensor X panic, low
battery” and the panel will
stop beeping for 4 hours.
1. The panel sends a Sensor Low Battery report to the central station.
2. The Status light turns on.
3. If Option 25: Trouble Beeps is enabled, six trouble beeps will sound once a minute.
When the low battery condition is fixed, the panel stops the trouble beeps and turns off the Status
light. See the sensor manual for information on replacing its battery.
Sensor Supervisory Failure
¾ If the panel does not hear from a sensor within the programmed RF Timeout (Option 15)
the following occurs:
1. The panel sends a Sensor Supervisory Failure report to the central station.
2. The Status light turns on.
3. If Option 25: Trouble Beeps is enabled, six trouble beeps will sound once a minute.
+
-
+
-
START MENU
MAIN MENU
Delete
press
Delete
To delete an option or access code
and follow voice prompts.
Cancel
Cancel
Minutes
See Note
DONE
, then
If you make a mistake or want to start
over press
Account No.
Add Option
I N S T R U C T I O N S
Add
Ad
d
Press
Clock Set
DONE
Option #
Press
Set Clock
Phone No.
Option #3:
Option #2:
Panel Voice Enable
Option #1:
Press for program information.
*
use red numbers to enter access code.
voice prompts.
Add Access Code
Hours
Access Code
See Note
Hold key or press repeatedly
until you hear the desired item.
Note:
See Note
Press and follow
Add
Cancel
Access Code
Sensor
Option #
*
*
Delete
Test
Clock Set
DONE
Hours
Minutes
422-3013 Rev A
2
4
5
3
1
8
9
0
7
6
+
-
+
-
START MENU
MAIN MENU
Delete
press
Delete
To delete an option or access code
and follow voice prompts.
Cancel
Cancel
Minutes
See Note
DONE
, then
If you make a mistake or want to start
over press
Account No.
Add Option
I N S T R U C T I O N S
Add
Ad
d
Press
Clock Set
DONE
Option #
Press
Set Clock
Phone No.
Option #3:
Option #2:
Panel Voice Enable
Option #1:
Press for program information.
*
use red numbers to enter access code.
voice prompts.
Add Access Code
Hours
Access Code
See Note
Hold key or press repeatedly
until you hear the desired item.
Note:
See Note
Press and follow
Add
Cancel
Access Code
Sensor
Option #
*
*
Delete
Test
Clock Set
DONE
Hours
Minutes
422-3013 Rev A
2
4
5
3
1
8
9
0
7
6
Battery Cover
Backup Battery
Slide cover off to the
right
Cover Screw
Speaker Screws
- CareGard 1
- GE Interlogix 2
- Contents 3
- Activity Check 18 4
- Medication Reminders 19 4
- Adding/Replacing Sensors 20 4
- Deleting Sensors 23 5
- System Monitoring 23 5
- Sensor Testing 25 5
- Troubleshooting 28 5
- About this 6
- Components 7
- Optional 7
- Setting up the 8
- Plugging in the Power 9
- Powering up the System 9
- Adjusting the Speaker Volume 9
- Access Codes 10
- Entering Program Mode 11
- Setting the Clock 11
- Changing an Access Code 11
- Programming 12
- A.M. Any time of day 13
- Option 10: Phone Mod 1 15
- Option 8: Phone Lock 15
- Option 9: Downloader Code 15
- Option 11: Phone Mod 2 16
- Option 13: DTMF Dialing 17
- Option 14: Auto Phone Test 17
- Option 15: RF Timeout 17
- Option 16: Manual Phone Test 17
- Option 20: Ring/Hang/Ring 18
- Option 27: RF Jam Detect 20
- Option 28: Access Code Length 20
- Option 29: RF Phone Answer 20
- Programming Options 22
- Exiting Programming Mode 23
- Resetting Memory to Defaults 23
- Medication 24
- Reminders 24
- Replacing 25
- Table 7: Programming Sensors 26
- Deleting 28
- Monitoring 28
- Sensor Low Battery 29
- Sensor Supervisory Failure 29
- Communication 30
- Pager Communication 31
- Voice Event Notification 31
- Remote Phone Operation 31
- System Function Phone Command 32
- Tal k 0 o r 1 32
- 2-Way Conversation 2 32
- Listen 3 or 6 32
- Terminate Session # 32
- Troubleshooting 33
Related products and manuals for Safety Ge 60-883-95R
Safety Ge Concord 4 User Manual
(72 pages)
(72 pages)
(33 pages)
Safety Ge 4 Series User Manual
(72 pages)
(72 pages)
Safety Ge 1000 User Manual
(36 pages)
(36 pages)
Safety Ge XLG3 User Manual
(160 pages)
(160 pages)
© 2020, manymanuals.com. All rights reserved. | 0.875 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals