GE NX-8V2 User Manual download pdf (Page 36)

NX-8V2 Control

LOC PG DESCRIPTION DEFAULT PROGRAM DATA

39 20 KEYPAD SOUNDER

Segment 1 (Circle numbers to program)

1 = Keypad sounds for Telephone Line Cut when in the Armed state.

2 = Keypad sounds for Telephone Line Cut when in the Disarmed state.

3 = Keypad sounds upon AC Power Failure.

4 = Keypad sounds upon Low Battery Detection.

5 = Keypad sounds during Cross Zone Trip Time.

6 = Keypad sounds for Tamper Alarm.

7 = Reserved.

8 = Keypad sounds for expander trouble (required for UL).

40 20 SYSTEM TIMERS

Segment 1 Dynamic Battery Test duration (0-255 minutes) 0 _

Segment 2 AC Failure report delay (0-255 minutes) 5 _

Segment 3 Power Up Delay (0-60 seconds) 60 _

Segment 4 Siren Time (1-254 minutes) 8 _

Segment 5 Telephone Line Cut delay (0-255 seconds) 0 _

Segment 6 Cross Zone Time (0-255 minutes) 5 _

Segment 7 Chime Time in 50 mS increments (0-255) 3 _

Segment 8 Dialer delay (15-255 seconds) 30 _

Segment 9 Fire Alarm Verification Time (120-255 sec.) 0 _

Segment 10 Listen-In Time (0-255 seconds) 0 _

Segment 11 Zone Monitor Timer (0-255 Days) 0 _

Segments 12 – 14 Reserved

41 20 SPECIAL FEATURES

Segment 1 (Circle numbers to program)

1 = Enables 6-digit code option. All arm/disarm/Go To Program codes require six digits

2 = Requires valid user code entry for [r]-[9]-[8] and [r]-[9]-[9] functions to work.

3 = Enable Auto Cancel / Abort.

4 = Enable Walk-Test Mode.

5 = Enable Auto Force-Arming with keyfob or keyswitch

6-8 = Reserved.

42 21 GO TO PROGRAM CODE 9-7-1-3-0-0 _ _ _ _ _ _

43 21 GO TO PROGRAM CODE PARTITION AND AUTHORIZATION

Segment 1 (Circle numbers to program)

1 = Reserved.

2 = Enables "Go To Program Code" as an arm only code.

3 = Enables "Go To Program Code" as an arm only after closing.

4 = Enables "Go To Program Code" as a master arm/disarm code (can change user codes)

5 = Enables "Go To Program Code" as an arm/disarm code.

6 = Enables "Go To Program Code" to bypass zones.

7 = Enables "Go To Program Code" opening and closing reports.

8 = Reserved.

Segment 2 (Circle numbers to program)

1 = Enables "Go To Program Code" for partition 1

2 = Enables "Go To Program Code" for partition 2

3 = Enables "Go To Program Code" for partition 3

4 = Enables "Go To Program Code" for partition 4

5 = Enables "Go To Program Code" for partition 5

6 = Enables "Go To Program Code" for partition 6

7 = Enables "Go To Program Code" for partition 7

8 = Enables "Go To Program Code" for partition 8

44 21 DURESS CODE 15-15-15-15-15-15 _ _ _ _ _ _

45 21 AUXILIARY OUTPUTS 1-4 PARTITION SELECTION

Segments 1 2 3 4

1 = Partition 1

2 = Partition 2

3 = Partition 3

4 = Partition 4

5 = Partition 5

6 = Partition 6

7 = Partition 7

8 = Partition 8

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 59 60

Comments to this Manuals

No comments

GE NX-8V2 User Manual Page 36

Comments to this Manuals

Related products and manuals for Security access control systems GE NX-8V2