GE NX-8V2 User Manual download pdf (Page 25)

SLOW COMMUNICATOR FORMAT CODES

NX-8V2 Control 25

77 OPENING COMMUNICATOR CODE 8............. numerical

Location 77 contains the digit of a 4+2 format if the "Opening Reporting" is enabled. Refer to the box on page 23.

Segment 1 = Partition 1 Segment 3 = Partition 3 Segment 5 = Partition 5 Segment 7 = Partition 7

Segment 2 = Partition 2 Segment 4 = Partition 4 Segment 6 = Partition 6 Segment 8 = Partition 8

78 CLOSING COMMUNICATOR CODE 8............. numerical

Location 78 contains the digit of a 4+2 format if the "Closing Reporting" is enabled. Refer to the box on page 23.

Segment 1 = Partition 1 Segment 3 = Partition 3 Segment 5 = Partition 5 Segment 7 = Partition 7

Segment 2 = Partition 2 Segment 4 = Partition 4 Segment 6 = Partition 6 Segment 8 = Partition 8

79 AUTOTEST COMMUNICATOR CODE 2............. numerical

Location 79 contains the digits for a 4+2 format that will be sent if the "Autotest" or "Manual Test" is enabled. Refer to the box on page

23.

80 RECENT CLOSING & EXIT ERROR COMM CODE 2............. numerical

Location 80 contains the digits for a 4+2 format that will be sent if "Recent Closing" and/or "Exit Error Reporting" is enabled. Segment

1 contains the digit for the "Recent Closing Reporting". Segment 2 contains the digit for the "Exit Error Reporting". Refer to the box on

page 23.

81 START PROGRAM & END PROGRAM COMM CODES 4............. numerical

Location 81 contains the digits for a 4+2 format that will be sent if "Start / End Programming Reporting" is enabled. Segment 1

contains the digit for the "Start Program Reporting". Segment 2 contains the digit for the "Start Program Reporting". Segment 3

contains the digit for the "End Program Reporting". Segment 4 contains the digit for the "End Program Reporting". Refer to the box on

page 23.

82 END DOWNLOAD COMMUNICATOR CODE 4............. numerical

Location 82 contains the digits for a 4+2 format that will be sent if "End Downloading Reporting" is enabled. Segments 1 and 2 are

Reserved. Segment 3 contains the digit of the "End Download Reporting". Segment 4 contains the digit of the "End Download

Reporting". Refer to the box on page 23. Note: A start download report will be sent to the internal event log.

83 CANCEL COMMUNICATOR CODE 1............. numerical

Location 83 contains the digit for a 4+2 format that will be sent if "Cancel Reporting" is enabled. Segment 1 contains the digit for the

"Cancel Communicator Reporting". Refer to the box on page 23.

84-87 RESERVED

LOCATIONS 88-109 ARE FOR PROGRAMMING DIFFERENT ACCOUNT CODES AND / OR FEATURES FOR EACH

PARTITION. IF A LOCATION IS LEFT UN-PROGRAMMED,

THE FEATURE FOR PARTITION 1 AND ACCOUNT CODE FOR THE PHONE NUMBER WILL BE USED.

88 ACCOUNT CODE FOR PARTITION 1 6............. numerical

Location 88 contains the account code sent when partition 1 is reported. If location 88 is left unprogrammed (all A10"s), then the

account code corresponding to the Phone number dialed will be used. If the account code is less than six digits, program a A10" in

the segment immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments.

89 ACCOUNT CODE FOR PARTITION 2 6............. numerical

Location 89 contains the account code sent when partition 2 is reported. If location 89 is left unprogrammed (all A10"s), then the

account code corresponding to the Phone number dialed will be used. If the account code is less than six digits, program a A10"

in the segment immediately after the last digit of the account code. If the account code is 6 digits long program all 6 segments.

90 PARTITION 2 FEATURE AND REPORTING SELECTIONS 5............. feature select

Location 90 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In

addition, certain communicator reports are enabled in this location. Each of these features can be enabled by partition. This location

contains 5 segments, with eight possible features per segment. Refer to Location 23 (page 15) for the feature selections. If all

segments are blank (nothing enabled), the features for partition 1 will be used.

91 PARTITION 2 ENTRY EXIT TIMERS 6............. numerical

Location 91 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid entries are 10-255

seconds. If all segments are A0", the entry and exit times for partition 1 will be used.

Segment 1, Entry time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.

Segment 2, Exit time 1: Exit time that will be used for all zones designated as Delay 1.

Segment 3, Entry time 2: Entry time that will be used when a Delay 2 zone type initiates an entry delay.

Segment 4, Exit time 2: Exit time that will be used for all zones designated as Delay 2.

Segments 5 & 6: Reserved

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 59 60

Comments to this Manuals

No comments

GE NX-8V2 User Manual Page 25

Comments to this Manuals

Related products and manuals for Security access control systems GE NX-8V2