35-201578-5N (1/01)
Reliez le fil de terre sur le fil vert, sur la vis verte de terre du
châssis ou la borne spécifique de terre.
N'enlevez pas les connecteurs isolés des fils non concernés
par le raccordement de la tension.
En changeant la tension des unités reconfigurables, ne bougez
que le fil avec la cosse isolée.
MONO-TENSION :
Tous les ballasts sont précâblés et l'utilisateur n'a qu'à relier les fils
d'alimentation pour la tension prévue.
MULTI-TENSIONS : (120/208/240/277 volts)
Reliez le fil de ballast avec sa terminaison isolée sur la borne de
tension adéquate comme indiqué sur la plaque du ballast.
MULTI-PUISSANCES :
Les ballasts multi-puissances sont disponibles en diverses
combinaisons de wattages. Reportez-vous aux instructions de
câblage sur l'étiquette à l'intérieur du luminaire.
LAMPES
N’utilisez que le type de lampe spécifié sur la plaque
d’identification. Observez les recommandations et restrictions
du fabricant sur le fonctionnement de la lampe, en particulier
pour le type de ballast, la position d’utilisation, etc.
Serrage de lampe - culot goliath : La lampe doit être insérée de
façon sûre avec un couple de serrage NEMA-EEI spécifié à 4,4 mkg (35
livre-pouce), ce qui est le mieux réalisé en serrant fortement à la main
pour mettre un couple suffisant. Le serrage doit complètement
appuyer et charger le contact central de la douille avec le culot de la
lampe.
ENTRETIEN
Le réflecteur en finition ALZAK
†
et la porte vitrée peuvent être
nettoyés avec toute solution convenable pour vitres non abrasive, à base
de savon ou de détergent, puis il faut les rincer à l'eau claire.
ATTENTION
Risque de brûlure
• Ne touchez pas le luminaire allumé
Risque de brûlure
• Laissez le bloc d’ampoule refroidir avant
d’y toucher
ATTENTION
GEH-5849
INSTRUCTIONS
P-154 Powerflood
®
Floodlight
READ THOROUGHLY BEFORE INSTALLING
AVERTISSEMENT; COUPER L’ALIMENTATION
AVANT L’INSTALLATION OU L’ENTRETIEN.
GENERAL
This luminaire is designed for outdoor lighting service,
and should not be used in areas of limited ventilation, or in
high ambient temperature enclosures. Best results will be
obtained if installed and maintained according to the
following recommendations.
UNPACKING
This luminaire has been properly packed so that no part
should have been damaged during transit. Inspect to
confirm.
INSTALLATION
WIRING
Make all electrical connections in accordance with
the National Electrical Code and any applicable
local code requirements.
Verify that supply voltage is correct by comparing it
to nameplate.
If unit is designated as multivolt or multiwatt,
follow specific instruction.
Three-conductor No. 14 cable (with 90°C minimum
insulation) is recommended for making electrical
connections to the P-154. After opening door loosen the 2
screws holding the reflector. Remove reflector thus expos-
ing the terminal board. Loosen screw in pressure plate,
insert cable through grommet and retighten screw. (Notice
that grommet fits cable of approximately 9/16-inch
diameter.) Grommet and pressure plate form a weather
proof seal and strain relief. To maintain this seal, the screw
in pressure plate must be retightened whenever the seal is
disturbed. After connections are made to the terminal
board, be sure insulating shield is properly placed.
CAUTION
Unit will fall if not installed properly
• Follow installation instructions
WARNING
Risk of electric shock
• Turn power off before servicing
– see instructions
The floodlight is provided with a trunnion bracket which
can be mounted directly on flat surfaces, or building fronts.
Mounting adaptors are available for installation on poles,
cross-arms, pipes, etc. The trunnion bracket has a clearance
hole for a 3/4-inch bolt used for attachment of such
mounting. The 1/2-inch holes on either side of the
3/4-inch hole permit additional anchoring, if required.
Tighten side trunnion bolts to 18 - 22 foot pounds.
AIMING
Slightly loosen bolts “A” (two on trunnion), tilt
luminaire to desired position and retighten bolts.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred
to GE Lighting Solutions.
g
GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
16943533----888
g
GE
Lighting Solutions
(62 pages)
(2 pages)
(4 pages)
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals