GE Valve Software Tools MN-Valvue-FF-IOM Service Manual Page 54
- Page / 244
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ValVueFF Software Interface to FVP
38
GE Energy
Tools Diagnostics Diagnostics dialog box used to diagnose a
selected device.
Query Device Query dialog box used to display a selected
device.
Re-Scan Devices Scan dialog box used to rescan the link for a
list of all devices.
Download Downloads the current configuration into a
selected device.
Download Firmware Downloads new firmware into a selected
device.
Set as Link Master Dialog box used to set a device as a link
master.
Reboot Device Dialog box used to restart a connected device.
Reboot device is available only to
Administrators.
For current selected device, if it is running as
LAS, a message refusing the reboot operation
appears.
Close Device Dialog box used to shut down a connected
device.
Help Help Topics The ValVueFF Help system.
About ValVueFF Returns a message box with ValVueFF version
number and copyright notice
Registration Information Registration information used to register this
software application.
Table 5 ValVueFF Menu Selections (Continued)
Menu Menu Item Display
- Masoneilan 1
- Products 1
- ValVue* FF (Rev B) 1
- Warranty 2
- Contents 3
- Safety Information 17
- Product Safety 18
- ValVueFF Specifications 21
- Getting Started With ValVueFF 23
- Wiring Requirements 26
- NI-FBUS Software 27
- ValVueFF Administration 33
- Installing ValVueFF 34
- Trial Period 42
- Registration 43
- ❑ Adding new user accounts 47
- Using ValVueFF 51
- Menu Bar 52
- Menu Bar 53
- Icon Toolbar 55
- Positioner Faceplate 57
- Active Faceplate 59
- Status Frame 61
- Selected Device Frame 61
- ❑ NORMAL 62
- ❑ MANUAL 62
- ❑ Out of Service 62
- Device Selection 63
- Setup Menu 65
- Configuration Services 71
- Device Tag/Address 73
- View Menu 74
- PID Controller 75
- Device Operation State 77
- Tools Menu 78
- Query Device 79
- Rescan Devices 80
- Help Menu 81
- Offline Use of ValVueFF 82
- Setup Wizard Procedure 83
- Step 1: Welcome 84
- Step 2: Actuator Wizard 85
- Step 3: Tuning Wizard 86
- Step 6: Finish Setup Wizard 93
- General Page 96
- Block Tag Info 97
- Others Installed 97
- Position Tab 98
- Position Limits Frame 100
- Limit Switch Threshold 101
- Fault Control 101
- Actuator Page 103
- Diagnostic Parameters 104
- Model and Serial Number 104
- AO Block Tab 105
- AO Block Options 106
- PID Block 108
- PID Control and Status Option 110
- Characterization Frame 112
- GE Energy 114
- ❑ Right-click the point 115
- - the distance from the 118
- Pressure Frame 119
- Others Frame 119
- Calibration Services 121
- Find Range Result 122
- Auto Stop Limits 122
- Manual Stop Limits 123
- Open Stop Adjustment 124
- Tuning Tab 125
- Auto Tune 127
- Travel Calibration Tab 128
- Calibrating 129
- Advanced Tab 131
- Overview 135
- PID Status Frame 136
- Simulation Function 137
- Others - Tuning Parameters 138
- PID Output and Valve Position 139
- Trending Overview 139
- Customizing the Trend 140
- Saving a Configuration 143
- Save to File 144
- Downloading to the FVP 145
- Download Firmware 147
- ❑ Right-click on Offline 148
- Diagnostic Services 151
- Self Check 152
- Performing a Self Test 152
- Self Test Explanation 153
- Signature Tab 154
- Signature Selection Frame 155
- Signature Measurement 156
- Signature Graphs 158
- ❑ Current 160
- ❑ Record 160
- ❑ Baseline 160
- ❑ Select File > Save 161
- Signature Notes 163
- Figure 126 Signature Notes 164
- 4. Enter notes and click OK 164
- Signature Setting Frame 165
- Extended Actuator Signature 167
- Step Response Test 169
- CAUTION The FVP must be OOS 170
- Step Response Test 173
- Positioner Signature 178
- Positioner Signature 179
- Query and Reporting Services 181
- Reporting Services 184
- Using Report Generation 185
- Communication Error Log 186
- Failsafe Handling 189
- Failsafe Clear Latched 190
- Failsafe Clear Non-Latch 190
- Exiting Failsafe 190
- Glossary 199
- Launching from Yokagawa and 209
- Figure 165 PRM Main Screen 210
- Launching from Yokagawa PRM 213
- Emerson Delta V Snap-On 214
- Configuring DI to TB 217
- Installing the PCMCIA Card 220
- Install the USB-8486 220
- Error Messages 223
- Online Diagnostics 224
- Block Error 225
- Foundation Fieldbus 227
- Reference Model Process 228
- P& I D 228
- Function Block Links 229
- ❑ Select the icon 231
- Block Modes 232
- Multiple Modes and States 233
- Transferring to Manual State 235
- Figure 181 Manual State 236
- Figure 182 Normal State 236
- RCas Mode 237
- Changing to Auto from OOS 238
- Information 240
- National Instruments 241
- GEA19795B 02/2012 244
Related products and manuals for Processors GE Valve Software Tools MN-Valvue-FF-IOM
Processors GE Calibur CBR-PB3-WD User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 1.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals