GE EPM 5300 User Manual Page 61
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 9: PROGRAMMING GROUP 0 – GLOBAL METER SETUP
GE Multilin EPM 5000 series Advanced Power Meters 57
HOW TO USE KYZ PULSE VALUE TABLE FOR MULTIPLICATION:
S
ITUATION 1: FSW=9999.
• Selection is Multiply by 2
• This means that every .5 unit WH =1 pulse.
• Unit=Kilo (see Group 1, Function 2)
• Result: For every 1 KWH increment on the
counter, the meter will output 2 pulses.
S
ITUATION 2: FSW=999.9
• Selection is Multiply by 2
• This means that every .05 unit WH=1 pulse.
• Unit=Kilo (see Group 1, Function 2)
• Result: For every 1 KWH increment on the
counter, the meter will output 20 pulses.
S
ITUATION 3: FSW=99.99
• Selection is Multiply by 20
• This means that every .0005 unit WH=1 pulse.
• Unit=Kilo (see Group 1, Function 2)
• Result: For every 1 KWH increment on the
counter, the meter will output 2,000 pulses.
S
ITUATION 4: FSW=9.999
• Selection is Multiply by 20
• Unit=Kilo (see Group 1, Function 2)
• This means that every .00005 WH=1 pulse.
• Result: For every 1 KWH increment on the
counter, the meter will output 20,000 pulses.
HOW TO USE THE KYZ PULSE VALUE TABLE FOR DIVISION:
S
ITUATION 1: FSW=9999.
• Selection is Divide by 10
• This means that every 10 unit WH=1 pulse.
• Unit=Kilo (see Group 1, Function 2)
• Result: For every 10 KWH increment on the
counter, the meter will output 1 pulse.
S
ITUATION 2: FSW=999.9
• Selection is Divide by 10
• This means that every 1 unit WH=1 pulse.
• Unit=Kilo (see Group 1, Function 2)
• Result: For every 1 KWH increment on the
counter, the meter will output 1 pulse.
S
ITUATION 3: FSW=99.99
• Selection is Divide by 20
• This means that every .2 unit WH=1 pulse.
• Unit=Kilo (see Group 1, Function 2)
• Result: For every 1 KWH increment on the
counter, the meter will output 5 pulses.
S
ITUATION 4: FSW=9.999
• Selection is Divide by 20
• Unit=Kilo (see Group 1, Function 2)
• This means that every .02 WH=1 pulse.
• Result: For every 1 KWH increment on the
counter, the meter will output 50 pulses.
To change the KYZ pulse value:
MAX/MIN
LIMITS
KVAR
PF
KW
KVA
FREQ
KWH
KVAH
AC VOLTS
AC AMPS
POWER
NCBA
MAX
MIN
A
N
B
N
C
N
A
B
B
C
C
A
LM2
LM1
NEXT
PHASE
VOLTS
AMPS
POWER
MAX/MIN
LIMITS
KVAR
PF
KW
KVA
FREQ
KWHKVAH
AC VOLTS
AC AMPS
POWER
NC
B
A
MA
X
MIN
A
N
B
N
C
N
A
B
B
C
C
A
LM2
LM1
NEXT
PHASE
V
OLTS
AMPS
POWER
MAX/MIN
LIMITS
KVAR
PF
KW
KVA
FREQ
KWH
KVAH
AC VOLTS
AC AMPS
POWER
NCBA
MAX
MIN
A
N
B
N
C
N
A
B
B
C
C
A
LM2
LM1
NEXT
PHASE
VOLTS
AMPS
POWER
Step 1:
a. Enter Group Level of
Programming Mode, (see Chp. 8).
b. Press MAX/MIN/LIMITS until 0.
appears in upper display.
c. Press AMPS to activate the
Group.
Step 2:
a. Press MAX/MIN/LIMITS until 06.P
appears in upper display.
! The lower display indicates
multiplication or division factor.
Step 3:
a. Press AMPS to change current
setting.
! The decimal point next to the 6
disappears.
b. Press MAX/MIN/LIMITS to
advance selections. -or-
c. Press VOLTS to reverse.
(Until desired factor appears).
! Division is indicated by div
appearing in the middle display.
When middle display is blank, it
indicates multiplication.
d. Press AMPS to store.
- Instruction Manual 1
- TABLE OF CONTENTS 3
- CHAPTER 1 5
- AC POWER MEASUREMENT 5
- 1.2: Three-Phase System 6
- 1) Delta 7
- 1.4: Waveform and Harmonics 8
- % THD GRAPH 8
- CHAPTER 2 9
- MECHANICAL INSTALLATION 9
- BACK VIEW 10
- CHAPTER 3 11
- ELECTRICAL INSTALLATION 11
- LIST OF CONNECTION DIAGRAMS 13
- EPM 5300P RELAY OVERVIEW 18
- CONNECTION FOR DB-9 FEMALE 21
- 5300P Instruments (rear view) 22
- Communications Port 23
- Model #SF485DB 23
- UNICOM 2500 24
- (Bottom View Shown) 24
- Model#SF485DB 25
- COMPUTER 27
- CHAPTER 5 31
- OVERVIEW 31
- AC VOLTS 32
- 5.6: Resetting Values 34
- UNPROTECTED RESET 35
- PROTECTED RESET 35
- 5.7: Resetting Hour Readings 36
- 5.10: Access Modes 38
- 5.11 Print Operating Data 38
- 5.12: Print Programming Data 39
- CHAPTER 6 41
- PROGRAMMING OVERVIEW 41
- SED FOR PROGRAMMING 42
- ASSWORD ENTRY 42
- CHAPTER 7 43
- EPM 5200P 43
- CHAPTER 8 45
- ENTERING PROGRAMMING MODE 45
- CHAPTER 9 47
- FUNCTION 50
- 9.5 Modbus Plus Capability 52
- PRINTING OPTION 52
- 9.7: Relay Mode 54
- DEFINITIONS: 54
- PROGRAMMING STEPS: 55
- CHAPTER 10 63
- SETTINGS 63
- VOLTAGE FULL SCALE: 64
- NTERING THE SCALE FACTOR: 65
- ECIMAL POINT SELECTION: 65
- YPE FULL SCALE 66
- CHAPTER 11 71
- CHAPTER 12 75
- AC AM PS 76
- RELAY 2 77
- SPECIAL CASES 78
- UNCTION 79
- Over/Under %THD Conditions 80
- 13.2: Trip Relay 83
- CHAPTER 14 87
- EXITING PROGRAMMING MODE 87
- CHAPTER 15 89
- PROGRAMMING QUICK REFERENCE 89
- 15.6: Group 2: Calibration 91
- 15.10: Group 6: THD Limits 92
- KEY DESIGNATIONS 93
- CHAPTER 16 95
- ETHERNET OPTION 95
- 16.2: Ethernet Option Setup 96
- 16.3: Default IP Address 97
- 16.4: AutoIP 97
- 16.5: Setting the IP Address 97
- 16.6: Network Configuration 98
- Multilin 100
Related products and manuals for Measuring, testing & control GE EPM 5300
(68 pages)© 2020, manymanuals.com. All rights reserved. | 0.607 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals