GE RV60 Installation Guide download pdf

imagination at work

Lighting

Retrot Installation Guide

BEFORE YOU BEGIN

Read these instructions completely and carefully.

CAUTION/ATTENTION

Risk of injury. While performing installations described, gloves, safety

glasses or goggles should be worn. / Risque de blessure. Lors de

l'exécution des installations décrites, des gants, des lunettes de sécurité

ou des lunettes de protection doivent être portées.

• The power supply must be supplied with 100-240 VAC,

50/60 Hz, and connected to an individual properly grounded

branch circuit, protected by a 15 or 20 ampere circuit breaker

or time delay fuse.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).

• Do not overload driver, follow installation instructions for the

GEPS6000NCMUL-SY or GEPS6500NCMUL-SY.

• Ensure that all connection points are sealed for damp

location using the appropriate method per the NEC or local

electrical code.

PREPARE ELECTRICAL WIRING

Electrical Requirements

WARNING/AVERTISSEMENT

Risk of electrical shock. Disconnect power before servicing or installing product.

LED Retrot Kit Installation requires knowledge of luminaires electrical systems. If

not qualied, do not attempt installation. Contact a qualied electrician. Install this

kit only in the luminaires that have the construction features and dimensions shown

in the photographs and/or drawings. / Risque de choc électrique. Couper le courant

avant de réparer ou installer le produit. LED Retrot Kit d’installation nécessite la

connaissance des systèmes luminaires électriques. Si vous n’êtes pas qualié, ne

tentez pas l’installation. Contactez un électricien qualié. Installez ce kit seulement

dans les luminaires qui ont les caractéristiques de construction et les dimensions

gurant sur les photographies et / ou des dessins.

Grounding Instructions–Cable Direct

• This lighting system must be connected to a grounded metal,

permanent wiring system, or an equipment grounding conductor

must be run with the circuit conductors and be connected

to the equipment grounding terminal.

• Installation to be performed by factory trained service

personnel only.

• For use inside a commercial refrigeration case with packaged

foods only.

• Use this unit only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

• Before installing, servicing or cleaning unit, switch power off

at the service panel and follow appropriate lock out/tag out

safety procedures

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown

throughout these instructions.

IMMERSION

LED Refrigerated Display Lighting

Vertical Cases

RV60 Series

Center Mullion Lights

48-inch: GELT604850CTR-SY/-SB (85742/85745), GELT604840CTR-SY/-SB (85748/85751), GELT604835CTR-SY/-SB (85754/85757)

60-inch: GELT606050CTR-SY/-SB (85699/85702), GELT606040CTR-SY/-SB (85705/85708), GELT606035CTR-SY/-SB (85711/85714)

67-inch: GELT606750CTR-SY/-SB (85717/85722), GELT606740CTR-SY/-SB (85725/85728), GELT606735CTR-SY/-SB (85736/85739)

Description Code (Single Unit Product Number/10-Pack Product Number)

LED DRIVER COMPATIBILITY

This system is compatible with GEPS6000NCMUL-SY or

GEPS6500NCMUL-SY LED Driver. Please refer to the separate

LED driver installation guide for appropriate wiring connections.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

1 2 3 4 5 6 7

Summary of Contents

Page 1 - IMMERSION

imagination at workGE LightingRetrot Installation GuideBEFORE YOU BEGINRead these instructions completely and carefully.CAUTION/ATTENTIONRisk of inju

Page 2

• For retrot only. If you are an OEM, please refer to the OEM Installation Guide.• Refer to manufacturing manual for refrigeration case to identi

Page 3 - Center LED Lights

WARNING/AVERTISSEMENTRisk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrot

Page 4 - Maximum LED Driver Loading

4CAUTION/ATTENTIONRisk of injury. Do not overload LED Driver. Do not exceed limits shown in “Maximum LED Driver Loading” table below. Risque de blessu

Page 5 - Connection Congurations

Connection Congurations4For information on A, B, C, D, see Steps 4, 5 and 6.WARNING/AVERTISSEMENTRisk of electrical shock. Ensure that all connection

Page 6 - Connect LED Driver - Input

6Connect LED Driver - OutputFor non-dimming applications, cap the unused wires with 5/32" (4mm) twist on wire connectors.Bundle and safely secure

• Tuck wires underneath Wire Cover before installing it onto the End Cap.• Attach Wire Cover to LED Light Mounting Tab by inserting a M2.9