GE PBS & PBP Installation Guide download pdf

GEH-5918

INSTRUCTIONS

SKYGARD

POWR/BRACKET

Retrofit Optical

READ THOROUGHLY BEFORE INSTALLING

35-201578-111 (3/04)

GENERAL

This luminaire optical is designed for outdoor lighting

service, and should not be used in areas of limited ventila-

tion, or in high ambient temperature enclosures. Best results

will be obtained if installed and maintained according to

following recommendations.

UNPACKING

This luminaire optical has been properly packed so that

no part should have been damaged during transit. Inspect to

confirm.

TOOLS

Installation will require either a slotted screw driver or

5/16 hex drivers.

INSTALLATION

After the luminaire optical has been unpacked and

inspected, it may be installed according to the following

instructions.

STEP 1

• Remove the lamp and retain.

• Remove the existing refractor optical by releasing the

bail latches as shown in Figure 1 and lowering the

optical to remove.

CAUTION

Risk of burn

• Allow lamp/fixture to cool before

handling

WARNING

Risk of electric shock

• Turn power off before servicing

– see instructions

STEP 2

If this is a 400 watt mercury Powr/Bracket go to STEP 6.

• Remove the socket bracket screws and lower the socket

and bracket from the casting shown in Figure 2.

• Retain the screws.

Figure 1

Figure 2

SKYGARD

™

Optical

New

Socket

Bracket

Release

Latches

Lower

Optical

Use Slotted

or 5/16

inch Hex

Driver

ÉTAPE 3

• Enlevez l'ancien étrier de douille sur la douille et jetez-le.

ÉTAPE 4

• Fixez le nouvel étrier en l'orientant conformément au

schéma de la figure 4.

ÉTAPE 5

• Réinstallez l'étrier avec la douille sur le bo

îtier du lumi-

naire, conformément à la figure 5.

Figure 4

Figure 6

Passer sur le crochet et tirer

vers le bas

Fermetures

à arceau

Figure 5

Vue du dessous

de la douille

Vue du dessus

de la douille

Nouvel étrier

coins coupés

Figure 3

Utilisez un tournevis à

empreinte hexagonale

ou un embout

hexagonal de 5/16 po.

Jetez le

vieil

étrier

ÉTAPE 6

• Fixez le module optique avec les fermetures à arceau, puis

réinstallez la lampe.

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred

to GE Lighting Solutions.

GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.

GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com

16943533----888

Lighting Solutions

1 2 3 4

Summary of Contents

Page 1 - Retrofit Optical

GEH-5918INSTRUCTIONSSKYGARDTM POWR/BRACKET®Retrofit OpticalREAD THOROUGHLY BEFORE INSTALLING35-201578-111 (3/04)GENERALThis luminaire optical is desig

Page 2 - AVERTISSEMENT

STEP 3• Remove the old socket bracket from the socket anddiscard.STEP 4• Attach the new bracket in the orientation shown inFigure 4.STEP5• Reattach th

Page 3

STEP 3• Remove the old socket bracket from the socket anddiscard.STEP 4• Attach the new bracket in the orientation shown inFigure 4.STEP5• Reattach th

Page 4

GEH-5918INSTRUCTIONSSKYGARDTM POWR/BRACKET®Retrofit OpticalREAD THOROUGHLY BEFORE INSTALLING35-201578-111 (3/04)GENERALThis luminaire optical is desig