GEH-5939
INSTRUCTIONS
M-250A2 Crimefighter Luminaire
READ THOROUGHLY BEFORE INSTALLING
GENERAL
This luminaire is designed for outdoor lighting service,
and should not be used in areas of limited ventilation, or in
high ambient temperatures. Best results will be obtained if
installed and maintained according to the following
recommendations.
UNPACKING
This luminaire has been properly packed so that no parts
should have been damaged during transit. Inspect to
confirm.
INSTALLATION
To mount, hold luminaire approximately level and snug
up bolts (4-5 foot-pounds). If more upward tilt of front of
luminaire is needed, loosen the bolts slightly, lift luminaire
and insert it to the next set of leveling steps. If downward tilt
is needed, reverse procedure by extracting the luminaire
from the pipe to sit on a more rearward set of steps.
Once the proper level has been achieved, tighten each
bolt to 10-12 foot-pounds, alternating between bolts. If a
torque wrench is not available, correct torque may be
achieved by turning bolts two to three full turns (or until
bottoming occurs) past their “snug position’’.
WARNING: UNDER NO CONDITIONS SHOULD
BOLTS BE TORQUED TO A LEVEL GREATER THAN
12 FOOT-POUNDS
PHOTOELECTRIC CONTROL
When used, photoelectric (PE) receptacle should be
oriented so that the word “North’’ is directed toward true
north. This is done by seating a PE control into receptacle,
lifting upward on PE control (which will lift PE receptacle
also), and rotating them clockwise until word “North’ is
directed toward true north. Then lower PE control and
receptacle to firmly seat them into position. No tools are
required to make this adjustment.
Alternatively, PE receptacle can be oriented before PE
control is installed. This is done by lifting up on rim of the
PE receptacle and rotating it until the word “North’’ is
directed toward true north. Lower PE receptacle to firmly
seat it in this position. Then install PE control.
WIRING
NOTE: Make all electrical connections in accordance
with the National Electrical Code and any applicable
local code requirements.
NOTE: Verify that supply voltage is correct by
comparing it to nameplate.
Terminals are readily accessible on terminal board and
will accept service leads ranging in size from AWG No. 14
through No. 6. Service leads (75° C minimum insulation,
90° C minimum for 200 & 250 watts) should extend
WARNING
Risk of electric shock
• Turn power off before servicing
– see instructions
CAUTION
Unit will fall if not installed properly
• Follow installation instructions
Remove power module ballast door by loosening captive
screw and opening door to a vertical position. Pull out
polarized disconnect plug which connects top housing
wiring with ballast door. Now grasp door securely in both
hands and open door further until it comes free from
hinges in top housing. This occurs at approximately 35
degrees from vertical on pole side of hinge. In this position
hinge pins will easily slide upward out of their hinge cradles
in top housing.
The pipe clamp accommodates 1 1/4 inch through 2
inch pipe. If necessary, adjust the two pipe clamp bolts so
that opening is slightly larger than pipe size being used.
Birdshield behind slipfitter clamp comes with an open-
ing for 1 1/4 inch pipe. If a larger pipe size is used, detach
knockout to provide a larger opening. Insert pipe carefully
through bird-shield and into back of the luminaire until it
hits the leveling steps which stick down from top of hous-
ing.
By selecting different steps, the luminaire may be
adjusted up or down with respect to pipe. A circular pad is
provided on top of housing for convenient application of
hand level.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred
to GE Lighting Solutions.
g
GE
Lighting Solutions
(32 pages)
(4 pages)
(5 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals