Ge DS-82 User Manual Page 206
- Page / 226
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 6: Command Line Interface
202 GE-DS-82 and 82-PoE Ethernet Managed Switch User Manual
show poe status
Description:
Show per PoE port information
Command Level
Global Configuration
Syntax:
show poe status [<port-list>]
Parameters:
<port-list> specifies the ports to be set. If not entered, all ports are set.
Example 1:
Switch(config)# show poe status 1
Port Admin Oper Priority Power Limit[W]
Current
Consumption [W]
Current[mA]
Device
Class
Port1 Enable on Low 15.4 13.4 279 0
Example 2:
Switch(config)# show poe status
Port Admin Oper Priority Power Limit[W]
Current
Consumption [W]
Current[mA]
Device
Class
Port1 Enable on Low 15.4 13.4 279 0
Port2 Enable on Low 15.4 11.3 236 0
Port3 Enable on Low 15.4 6.5 135 3
Port4 Enable off Low 15.4 0 0 0
Port5 Enable off Low 15.4 0 0 0
Port6 Enable off Low 15.4 0 0 0
Port7 Enable off Low 15.4 0 0 0
Port8 Enable off Low 15.4 0 0 0
Port9 Enable off Low 15.4 0 0 0
Port10 Enable off Low 15.4
0
0
0
- GE-DS-82 and 82-PoE Ethernet 1
- Managed Switch User Manual 1
- Content 3
- Chapter 1 5
- Introduction 5
- Package Contents 6
- Product Description 6
- How to Use this Manual 8
- Product Features 8
- Chapter 1: Introduction 10
- Product Specifications 11
- Chapter 1: Introduction 13
- Chapter 2 15
- Installation 15
- LED Indications 16
- Chapter 2: Installation 17
- Switch Rear Panel 18
- Switch Installation 20
- Rack-mount Installation 21
- SFP Transceiver Installation 22
- Chapter 2: Installation 24
- Chapter 3 27
- Switch Management 27
- Management Access Overview 28
- Web Browser Management 29
- Web Browser Setup 30
- Figure 12 31
- The Administration Console 32
- Direct Access 33
- Protocols 34
- SNMP Protocol 36
- Management Architecture 36
- Chapter 4 37
- Web-Based Management 37
- Requirements 38
- Logging on to the Switch 39
- Main Web Page 40
- Main Menu 41
- System Information 42
- SNMP Configuration 47
- Firmware Upgrade 55
- Configuration Backup 57
- Factory Default 59
- Syslog Setting 60
- Port Configuration 60
- Port Status 63
- Port Statistics 63
- Port Sniffer 65
- Protected Port 67
- Static VLAN Configuration 71
- Port-Based VLAN 72
- 802.1Q VLAN 75
- 2. Fill QinQ Tpid 83
- GVRP VLAN 84
- GVRP Setting 84
- GVRP Table 86
- Rapid Spanning Tree 87
- Illustration of STP 90
- STP Parameters 92
- RSTP System Configuration 93
- Trunking 98
- Aggregator Setting 99
- Aggregator Information 100
- State Activity 104
- Forwarding and Filtering 105
- Static MAC Table 106
- MAC Filtering 107
- OBJECT DESCRIPTION 108
- IGMP Snooping 109
- Idle Member 112
- Non-Member 112
- Delaying Member 112
- IGMP Configuration 113
- QoS Configuration 114
- TOS/DSCP 117
- 4 bit 4 bit 6 bit 2 bit 118
- Access Control List 120
- IPv4 ACL 121
- Non-IPv4 ACL 123
- MAC Limit 125
- MAC Limit Port Status 126
- 802.1X Configuration 127
- System Configuration 131
- 802.1x Port Configuration 132
- Misc Configuration 134
- Power Over Ethernet 135
- DHCP Relay and Option 82 139
- Chapter 5 143
- Console Management 143
- Configure IP address 145
- Commands Level 147
- Chapter 6 149
- Command Line Interface 149
- System Commands 150
- Switch Static Configuration 151
- Description: 155
- Trunk Configuration 156
- LACP Commands 157
- LACP is enabled 158
- LACP system priority: 32768 158
- VLAN Configuration 159
- VLAN Mode: Port-based 160
- Administration Configuration 171
- IP Configuration 172
- Reboot switch 173
- Reset to Default 173
- TFTP Update Firmware 174
- Restore Configure File 174
- Backup Configure File 175
- MAC limit 176
- Port Mirroring Configuration 177
- Quality of Service 178
- Per Port Priority 180
- MAC Address Configuration 181
- STP/RSTP Commands 183
- System Options 188
- Community Strings 190
- Trap Managers 191
- 802.1x Protocol 194
- Non-Ipv4 ACL commands 201
- Binding 203
- Display System PoE status 205
- Configure PoE - System 207
- Configure PoE -- Port 209
- Chapter 7 213
- Switch Operation 213
- Store-and-Forward 214
- Auto-Negotiation 214
- Chapter 8 215
- Overview 215
- PoE System Architecture 216
- The PoE Provision Process 218
- Line Detection 219
- Classification 219
- Start-up 219
- Operation 219
- Power Overloads 220
- DC Disconnect 220
- AC Disconnect 220
- Chapter 9 221
- Troubleshooting 221
- Chapter 9: Troubleshooting 222
- Appendix A 223
- RJ-45 Pin Assignment 223
- 10/100Mbps, 10/100Base-TX 224
Related products and manuals for Computer Accessories Ge DS-82
Computer Accessories Ge ML2400 User Manual
(62 pages)
(62 pages)
(28 pages)© 2020, manymanuals.com. All rights reserved. | 1.435 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals