GE SAM Installation Guide download pdf

GEH-5982

INSTRUCTIONS

Type 201 SA Luminaire

READ THOROUGHLY BEFORE INSTALLING

CAUTION: Type 201 SA luminaire is designed for outdoor lighting and should not be

used in areas of limited ventilation, or in high ambient temperature enclosures.

Check to see if opening of mounting bracket arm clamp in slip tter is large enough to allow

mounting bracket to be inserted. If not, loosen two clamp bolts until opening is large enough.

The slip tter is then inserted over outboard end of mounting arm, mounting arm being

inserted until it comes to rest at pipe stop on inboard end of slip tter (approx. 2 ½-inches).

Once mounting bracket is fully inserted, level hood with mounting bracket clamp relatively

loose, by placing outboard end of mounting bracket on appropriate step of leveling pipe

stop, then tighten two clamp bolts securely, taking care not to disturb position of hood;

torque should be approx. 10-15 foot-pounds.

NOTE: The mounting bracket clamp is factory installed for use with a 1¼-inch pipe. If a 2

inch pipe is being used it will be necessary to ip the mounting arm clamp over.

Unit will fall if not installed properly

• Follow installation instructions

CAUTION

WARNING

Risk of electric shock

• Turn power o before servicing

– see instructions

Type 201SA

Conduit Mounting

CAUTION

Risk of burn

• Do not touch operating luminaire

CAUTION

Risk of injury

• Wear safety glasses and gloves during

installation and servicing

Type 201 SA luminaire, unit pack, is designed for mounting on a round wood pole. (See

above illustration for identication and location of parts.) The mounting bracket should rst

be mounted to pole. A clearance hole for a 5/8-inch diameter bolt must be drilled through

pole. The 10-inch through bolt should be inserted through clearance hole and 2-inch

square washer and nut screwed loosely onto opposite end of through bolt. The pole plate

on mounting arm should be placed over square head of through bolt so that square head

is engaged by two indented tabs on pole plate. (See illustration 1).

SEE ILLUSTRATION 2

Nut should be tightened down so that mounting bracket

arm is securely attached to pole. Lag bolts should be

inserted into outside lower holes of mounting bracket arm

pole plate. Hammer lag bolts in to within approximately

1” of head, then tighten down with wrench.

The leads from hood should rst be inserted through

outboard end of the mounting bracket and brought out

through inboard end adjacent to the pole plate.

It is recommended a drip loop be formed where leads exit

mounting bracket as indicated in above drawing.)

CAUTION

Risk of burn

• Allow lamp/xture to cool before handling

Wiring

NOTE: Make all electrical connections in accordance with the National Electrical Code

and any applicable local code requirements including grounding

NOTE: Verify that supply voltage is correct by comparing it to nameplate.

Terminals are readily accessible on terminal board and will accept service leads ranging

in size from AWG No. 16 through No. 6. Service leads

FOR Special option catalog number with 240-volt primary ballast operation and 120

volt PE operation.

Connect incoming 240 volt to xture black wires and connect the incoming white wire to the

xture white wire.

Lamp Installation

NOTE: Use only lamps specied on nameplate. Observe lamp manufacturer’s recom-

mendations and restrictions on lamp operation; particularly ballast type, burning position,

etc.

Installation of optical assembly to hood

Optical assembly should be handled carefully to prevent

damage from surface abrasion or

severe impact. Attach optical

assembly to hood by snapping two latches on reector to “ears’’

on hood.

(See illustration 5.)

ILLUSTRATION 5

Nut

Square Washer

Thru Bolt

Extension Arm

Lag Bolts (4)

Mounting Bracket

ILLUSTRATION 1

ILLUSTRATION 2

ILLUSTRATION 4

ILLUSTRATION 3

(P)

Lift, Twist

and Reseat

(S)

(R)

(P)

(Q)

To orient the photoelectric receptacle

(See illustration 3)

Grasp spring loaded PE control receptacle (P) and

lift up, rotate receptacle clockwise until “North’’ arrow

(Q) printed on top of receptacle points North. Reseat

receptacle. If this orientation prevents light from reach-

ing control window (R), rotate arrow to point South.

To install the photoelectric control

(See illustration 4)

Insert the PE control (S) in its’ proper keyed socket

slots on top of xture, making certain that the largest

of the three prongs is inserted onto the slot located

adjacent to the word “North’’ on the socket. Press

downward and twist clockwise about 1/8 of a turn

to secure.

Lighting Solutions

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular problems arise which are not covered suciently for the purchaser’s purposes, the matter should be referred to

GE Lighting Solutions.

1 2

Summary of Contents

Page 1 - Type 201 SA Luminaire

GEH-5982INSTRUCTIONSType 201 SA LuminaireREAD THOROUGHLY BEFORE INSTALLINGCAUTION: Type 201 SA luminaire is designed for outdoor lighting and should n

Page 2 - 1 6 9 4 3 5 3 3- - -- 8 8 8

35-201578-174 (8/08)gGE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solution