Ge HC HP User Manual download pdf (Page 13)

GE MDS Intrepid-HC HP Installation Guide 1-7

Assembling the Pole Mount Kit

The Pole Mount Kit is used to connect the Hanger Kit (together with the RFU and OCB) to the pole.

The kit consists of a single metal plate with a clamp assembly.

Important: The diameter of the pole upon which the kit is mounted must be between 50 mm (2") and

125 mm (5").

To assemble the Pole Mount Kit on the pole:

1. Open the Pole Mount Kit clamp, and assemble the kit on the pole, as shown in the following illustration.

2. Fasten the kit to the pole using the 4 screws, as shown in the photo above.

Four Screws

Fastening the

Pole Mount Kit

to the Pole

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 113 114

Intrepid-HC HP 1
Table of Contents 3
CLASS 1 LASER PRODUCT 4
子信息品有毒有害物申明 5
Chapter 1: Installation 7
GE MDS Intrepid-HC HP RFU 8
1+0/1+1 Installation 10
Assembling the Hanger Kit 12
Four Screws 13
Fastening the 13
Pole Mount Kit 13
RFU Cable Connections 17
2+2 XPIC Installation 18
Installation Components 19
Installation Procedure 19
N+1 Split Mount Installation 22
1+0 Configuration 25
1+0 SD Configuration 25
1+1 HSB Configuration 26
1+1 SD Configuration 26
1+1 FD Configuration 27
1+1 FD/SD Configuration 27
1+1 SD BBS Configuration 28
2+0 DP Configuration 29
2+0 SD DP Configuration 29
2+0 SP Configuration 30
2+0 SD SP Configuration 30
2+2 Hot Standby Dual Pole 31
2+2 HSB SP Configuration 32
2+2 SD DP Configuration 33
2+2 SD SP Configuration 34
2+2 FD SP Configuration 35
2+2 HSB FD DP Configuration 36
2+2 SD/FD DP Configuration 37
4+1 FD DP Configuration 38
5+1 FD DP Configuration 39
4+1 FD SD DP Configuration 40
5+1 FD SD DP Configuration 41
Defining IP Addresses 45
To define IP Addresses: 46
NMS PC Requirements 47
Starting the NMS 48
External Alarms Setup 54
Exiting the NMS 55
##*3 floorshelfIPbaseIP ++= 58
shelves. The subnet is not 59
Connecting Line Interfaces 74
Procedures 75
Site Acceptance Procedure 76
1+0 Commissioning Procedure 81
Management Verification 82
Loopback Operation 82
1+1 Commissioning Procedure 83
Switching Tests 84
XPIC Installation Guidelines 86
XPIC Commissioning Tests 87
XPIC Recovery Verification 88
2+2 Verification 88
3-15 89
3-17 91
Protection Connector Pin-Out 95
8 x E1/T1 Connector Pin-Out 95
E1/T1 Connector Pin-Out 97
10BaseT Connector Pin-Out 97
Configuring PPP 99
General 101
Frequency Channels 101
6H GHz (6.45-7.1 GHz) 104
7 GHz (7.1-7.9 GHz) 105
ITU-R 385-7 [0] 107
8 GHz (7.8-8.5 GHz) 111
IN CASE OF DIFFICULTY 113

Comments to this Manuals

No comments

Ge HC HP User Manual Page 13

Comments to this Manuals

Related products and manuals for Hardware Ge HC HP