Ge ZTGD Series Transfer Switches 40-3000 Amps User Manual Page 9
- Page / 36
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
■
GE Zenith Controls 9
■
ZTG/ZTGD Operation and Maintenance Manual (70R-1000D)
MX150 Microprocessor Controller (cont’d)
Figure 8
LCD & Keypad
These options are accessible through the LCD and
keypad (see figure below). To become familiar with the
options loaded into a particular unit, scrolling through
the SET and CFG menu will show the descriptions of
the options (see pages 17). These menus are the very
same menus that are used to access the setting and/or
configuration of these options. The SET (setting) menu
is primarily used to show or change, time and voltage
settings. The CFG menu is primarily used to turn an
option on or off. When scrolling through these menus,
MX150
S1 OK
01: 50
FRI 31 MAY 2003
Source 2 (Red)
indicates Source 2
is acceptable for use
Source 1 LED (Green)
indicates Source 1 is
acceptable for use
Exercise Event
"Impending"
SET Menu
MORE CFG TEST SET
#1 or the word
on the LCD above the key.
The word above the key
changes depending on which
screen is being displayed.
#2 or the word
on the LCD above the key.
The word above the key
changes depending on which
screen is being displayed.
#3 or the word
on the LCD above the key.
The word above the key
changes depending on which
screen is being displayed.
#4 or the word
on the LCD above the key.
The word above the key
changes depending on which
screen is being displayed.
Current Time,
Day and
Date of Display
Source 1 Position LED (Green)
indicates Power Panel (ATS)
is closed to Source 1 position
Source 2 Position
LED (Red) indicates
Power Panel (ATS)
is closed to
Source 2 position
MORE Menu
CFG Menu
TEST Menu
Keypad
* E *
LCD Screen
no changes can be made without entry of the access code.
The factory set six-digit access code is located on a white
label on the back of the unit (see figure 9 pgs. 17-19).
The MX150 has many logic options. Each controller is
downloaded with options at the time of manufacture.
The collection of options that any one controller has is
specified at the time of order placement. The following
pages include all the options that can reside in the
controller. Not all units include all options.
- GE Zenith Controls 1
- Table of Contents 2
- Introduction 2
- Authorized Service 2
- Safety / Installation 3
- Installation (cont’d) 4
- MX150 Controller 8
- LCD & Keypad 9
- (Delayed Transition Only) 10
- (cont’d) 11
- CDP (replaces CDT) 12
- Optional Accessories 13
- How to Set the System Clock 14
- CDT One Event Timer Exerciser 14
- GE Zenith Controls 15 15
- CDP Clock Exerciser 16
- MX150 User Setup - CFG Menu 17
- MX150 User Setup - SET Menu 18
- FRI 31 MAY 2003 19
- MORE TEST 19
- SYSTEM TEST 20
- FAST XFR NO 20
- MORE TEST LOAD XFR 20
- Sequence of Operation 21
- Controls Power Supply (CPS) 22
- General Troubleshooting 24
- Maintenance and Testing 25
- T1 T2 T3 TN 26
- E1 E2 E3 EN 26
- N1 N2 N3 NN 26
- 40-80 Amps 30
- 600 Amps 30
- 100-400 Amps 30
- SCR-N/SCR-E 31
- SCR PS-8896 31
- SCR-NO/SCR-EO 31
- GE Zenith Controls 33 33
- 34 GE Zenith Controls 34
- GE Zenith Controls 35 35
- Zenith Controls 36
Parkside PAS 500 B1 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Staubsauger Parkside PAS 500 B1.
Wir stellen 4 PDF-Handbücher Parkside PAS 500 B1 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comments to this Manuals