ProBridge Ethernet User Manual
ProBridge EthernetUser Manual64310-0007 120 VAC power supplyPower supply input• Voltage: 120 VAC• Tolerance: ± 10%• Frequency: 60 HzPower supply outpu
7InstallationBefore installation, please familiarize yourself with the PBe and its typical system layout.PBe componentsFigure 2. PBe landmarksPower co
ProBridge EthernetUser Manual8Typical system layoutThe following figure shows a typical multiple ATM layout.Figure 3. Multiple ATM system layout RS232
9Installation overviewThe basic steps required to install the PBe are:1. Physically connect the PBe interface to the network switch or hub and the DVR
ProBridge EthernetUser Manual10Required DIP switch informationImportant switch assignmentsTable 1. Important switch assignmentsDefault switch settings
11setting switches 5-8 on SW1. See SW1 switches 5 to 8 on page 21.2. Connect the PBe to the network switch or hub using the supplied 4310-0040 Etherne
ProBridge EthernetUser Manual12ProgrammingAfter you install the PBe, you need to program the ProBridge for operation. This is accomplished by using Hy
13Figure 4. Laptop connected to PBe4. The Connection Description dialog box will display. Type in a name for this session (PBe) and click OK.5. The Co
ProBridge EthernetUser Manual14Figure 5. HyperTerminal programming mode2. Press the Enter key twice to bring up the Main Menu.Figure 6. Main menu
15Main MenuThere are five menu selections on the Main Menu:• Exit - Exits the maim menu and saves any changes.• PBe Set-up - provides IP address setup
ATM ProBridgeUser Manualii Copyright Copyright © 2006, GE Security Inc. All rights reserved. This document may not be copied or otherwise reproduce
ProBridge EthernetUser Manual16the list will be selected. The PBe supports the following Ethernet devices:• Generic interface• Native ATM messages (FC
174. The camera/terminal will redisplay with the new information. 5. Pressing the enter key will terminate the camera/terminal IP set-up and return yo
ProBridge EthernetUser Manual18ins entered followed by the enter key. Changing the selection to on allows the PBe to monitor the incoming Ethernet pac
193. Set the DIP switches per the tables in DIP switch settings on page 20 to match the changes desired.4. Reconnect the PBe to the DVR.5. Reapply pow
ProBridge EthernetUser Manual20DIP switch settingsThis chapter deals in detail with the DIP switch settings. The PBe must be re initialized before any
21SW1 switches 5 to 8Switches 5 to 8 on SW1 are for associating a specific camera on the DVR to the PBe.Table 4. SW1 switches 5 to 8 - Camera number s
ProBridge EthernetUser Manual22SW3 switches 1 to 8The switch positions on SW3 are for selecting the Ethernet device type.These switches are reserved f
23Accessing the WebserverThe PBe has a built-in webpage for simple configuration changes and remote upgrade. To access the webpage do the following:1.
ProBridge EthernetUser Manual24Figure 10. The PBe home pageClick on any of the hyperlinked text to navigate to that feature’s page.
25TroubleshootingUse the table below to solve some of the most common problemsTable 7. Troubleshooting tableProblem Probable cause SolutionNo red LEd
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Conventions used in this document .
ProBridge EthernetUser Manual26Technical specificationsPBeGeneralEnvironmentalElectricalHousing: Metal enclosureDimensions: 4 x 7 x 1.5 in. (100 x 175
27Cable SpecificationsPBe to DVR Figure 11. 4310-0034B cablePart number: 4310-0034B Communication type: RS-232Connector type: RJ45Length: 5 ft. (1.52
ProBridge EthernetUser Manual28PBe to PC Figure 12. 4310-0061 cablePart number: 4310-00061 Communication type: RS-232/Null ModemConnector type: DB9-F
29PBe Ethernet cable Figure 13. 4310-0040 PBe Ethernet Part number: 4310-0040Communication type: EthernetConnector type: RJ45, RJ45length: 6 ft. (1.83
ProBridge EthernetUser Manual30Contacting technical supportFor assistance installing, operating, maintaining, and troubleshooting this product, refer
ProBridge EthernetUser Manualiv
1IntroductionThis is the GE ProBridge Ethernet User Manual for model PBe. This document includes detailed instructions explaining:• how to setup and i
ProBridge EthernetUser Manual2Conventions used in this documentThe following conventions are used in this document: Safety terms and symbolsThese term
3OverviewThe PBe is a specific ProBridge unit for interfacing the DVR family of digital video multiplex/recorders to financial institution automated t
ProBridge EthernetUser Manual4Product contentsThe PBe system consists of the ProBridge unit, this manual, an Ethernet cable, a PBe to DVR cable, a PBe
5Installation environmentPower. Ensure that the installation site’s AC power is stable and within the rated voltage of the external power supply.
Comments to this Manuals