Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com Turn to Select Press to
10 ALIGNING THE WALL PLATE Draw a vertical line on the wall at the center of the 30s wide space. Use the mounting plate as the template for the rear
Turn to Select Press to EnterAThis oven is designed for adaptation to the following 3 types of ventilation: A. Outside Top Exhaust (Ve
Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.NOTE: Before tightening toggle b
13MOUNT THE OVENA4 ASSEMBLE AND INSTALL ADAPTORA3 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINETYou need to drill holes for the top support s
CONNECTING DUCTWORK143 Attach the oven to the top cabinet. Turn to Select Press to Enter5Cabinet FrontCabinet Bottom ShelfFiller BlockO
OUTSIDE BACK EXHAUST (Horizontal Duct) PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUSTB1 Turn to Select Press to EnterINSTALLA
BEFORE: Fan Blade Openings Facing Up4321 Remove the three screws that hold the blower plate to the oven. Slide blower plate from under its retainin
Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow. Locate the two “knockout” plates, on the rear oven panel,
Attach the oven to the top cabinet. Turn to Select Press to Enter18Installation InstructionsMOUNT THE OVENB585Cabinet Front7 Tighten
USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINETC2 19 RECIRCULATING (Non-Vented Ductless) Turn to Select Press to EnterINST
2 Recirculating ... 19–22 Attach Mounting Plate to Wall ...19 Preparation of Top Cabine
AFTER: Fan Blade Openings Facing Forward324ADAPTING BLOWER FOR RECIRCULATIONC320NOTE: The exhaust adaptor with damper is not needed for recirculati
Place the blower unit back into the opening. WARNING:5LVNRIHOHFWULFVKRFNcan cause injury or death. Do not pull or stretch WKHEORZHUXQLW
Remove 2 screws on top of oven, just above the grille panel, using a Phillips screwdriver. Open the door.Remove the grille. Slide the grille to the l
KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE. 120 V Models: Plug power cord into a dedicated 15- to 20-amp electrical outlet.7Re
24Printed in Korea49-40679-1MFL59060907(04-13 GE)
¿Preguntas? Llame 800.GE.CARES (800.432.2737) o visite nuestra página en la red en: GEAppliances.com Turn to Select Press to EnterLEA CU
26 Recirculación ... 43–46 Cómo adherir la placa de montaje a la pared ...
Este producto requiere un tomacorriente eléctrico de tres patas conectado a tierra. El instalador debe llevar a cabo una inspección de continuidad a
28 LONGITUD NÚMERO LONGITUDPARTES DEL CONDUCTO EQUIVALENTE x USADO = EQUIVALENTE Tapa del techo 24 pies x (1) =
* IMPORTANTE: Si se usa un adaptador de transición de rectángulo a redondo, las esquinas del fondo del regulador de tiros deberán ser cortadas para q
A qualified electrician must perform a ground continuity check on the wall receptacle before beginning the installation to ensure that the outlet box
PARTE CANTIDAD Tornillos de madera 2 (1ø4s x 2s) Tornillos basculantes 4 (y tuercas de mariposa) (1ø4s x 3s) Tornillos de máquina
31HERRAMIENTAS QUE NECESITARÁDestornilladores de estrella # 1 y # 2LápizRegla recta y cinta métricaEscuadra de carpintero (opcional)Tijeras para cort
32 Encuentre los postes, usando uno de los métodos siguientes: A. Use un detector de postes – un dispositivo magnético que localiza clavos.O B.
33CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE SU GABINETECSus gabinetes podrían tener marcos de decoración que interfieran con la
34 CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Trace una línea vertical en la pared en el centro del espacio de 30s de ancho. Use el plato de m
Turn to Select Press to EnterA TIPOS DE INSTALACIÓN (Escoja A, B o C)Este horno está diseñado para adaptarse a los siguientes tres
Coloque el plato de montaje contra la pared e inserte las alas de mariposa en los agujeros de la pared para montar el plato.NOTA: Antes de apretar l
37 ENSAMBLAJE E INSTALACIÓN DEL ADAPTADORA3 USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIORDeberá perforar agujeros
383 Pegue el horno a la parte superior del gabinete. Turn to Select Press to Enter765 Apriete los dos tornillos exteriores hacia la par
ESCAPE POSTERIOR EXTERNO (Conducto horizontal) CÓMO PREPARAR LA PARED POSTERIOR PARA EL ESCAPE POSTERIOR EXTERIORB1 Turn to Select
4HOOD EXHAUSTNOTE: 5HDGWKHVHQH[WWZRSDJHVRQO\LI\RXSODQWRYHQW\RXUH[KDXVWWRWKHRXWVLGH,I\RXSODQWRUHFLUFXODWHWKHDLUEDFNLQWRWKHUR
ANTES: LAS ABERTURAS DE LA PALETA DEL VENTILADOR ESTÁN ORIENTADAS HACIA ARRIBA4321 Remueva y guarde los tornillos que sostienen el plato del
Localice los dos platos removibles en el panel posterior del horno, cerca de la parte superior del horno. Usando tijeras, cuidadosamente corte
Turn to Select Press to Enter Pegue el horno a la parte superior del gabinete. Turn to Select Press to Enter42Instruccio
USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIORC2 43 RECIRCULACIÓN (Sin conducto de ventilación) Turn t
DESPUÉS: LAS ABERTURAS DE LA PALETA DEL VENTILADOR ESTÁN ORIENTADAS HACIA ADELANTE324 CÓMO ADAPTAR EL CALEFACTOR PARA LA RECIRCULACIÓNC344NOTA: El ada
765 CÓMO ADAPTAR EL CALEFACTOR PARA LA RECIRCULACIÓN (continuación)C345 Coloque la unidad del calefactor de nuevo en la abertura. ADVERTENCIA: E
53421 CÓMO INSTALAR EL FILTRO DE CARBONILLAC5 CÓMO MONTAR EL HORNO (continuación)C4 Inserte el filtro en horno como se muestra hasta que se ajuste
GUARDE ESTAS INSTRUCCIONES PARA EL USO DEL INSPECTOR LOCAL. (continued) Modelos de 240 V: El tomacorriente de pared recomendado para este aparat
Printed in Korea Impreso en Corea49-40679-1MFL59060907(04-13 GE)
EQUIVALENT NUMBER EQUIVALENTDUCT PIECES LENGTH x USED = LENGTH Rectangular-to-Round 5 Ft. x ( ) =
PART QUANTITY Top Cabinet 1 Template Rear Wall 1 Template Installation 1 Instructions Separately 2 Packed Grease Filte
7TOOLS YOU WILL NEED# 1 and #2 Phillips screwdriverPencilRuler or tape measure and straight edgeCarpenter square (optional)Tin snips (for cutting damp
8 Find the studs, using one of the following methods: A. Stud finder – a magnetic device which locates nails.OR B. Use a hammer to tap lightly ac
9DETERMINING WALL PLATE LOCATION UNDER YOUR CABINETCYour cabinets may have decorative trim that interferes with the oven installation. Remove the deco
Comments to this Manuals