GE GUD24GSSJWW Instruction Manual download pdf (Page 10)

Installation Instructions

PLUMBING INFORMATION WATER

SUPPLY REQUIREMENTS

• HOT AND COLD WATER FAUCETS – Must be within 42”

of the appliance water inlet hose connections. The

faucets must be 3/4” garden hose-type so inlet hoses

can be connected.

• WATER PRESSURE – Must be between 10 and 120

pounds per square inch with a maximum unbalance

SUHVVXUHKRWYVFROGÀRZLQJRISRXQGVSHUVTXDUH

inch.

• WATER TEMPERATURE – Water heater should be set to

GHOLYHUWR)WR&LQWKHZDVKHUZKHQ

HOT wash is selected.

 6+872))9$/9(6²%RWKKRWDQGFROGZDWHUVKXWRȺ

valves (faucets) should be supplied.

• LOCATION – Do not install appliance in an area where

the temperature will fall below freezing. If appliance

is stored or transported in freezing temperatures, be

VXUHDOOZDWHUIURPWKH¿OODQGGUDLQV\VWHPVKDVEHHQ

removed.

DRAIN REQUIREMENTS

• DRAIN RATE – The drain or standpipe must be capable

RIDFFHSWLQJDGLVFKDUJHDWWKHUDWHRIJDOORQVSHU

minute.

• DRAIN HEIGHT – The drain height must be 33” minimum

DQGµPD[LPXP

CONNECTING TO PLUMBING

FACILITIES

If not installed, install rubber washer in one end of hot water

hose. Thread hot water hose onto connection labeled H at

top rear of washer. Hand tighten, plus an additional 1/8 turn

with pliers.

If not installed, install rubber washer in one end of cold water

hose. Thread cold water hose onto connection labeled C at

top rear of washer. Hand tighten, plus an additional 1/8 turn

with pliers.

0RYHDSSOLDQFHDVFORVHWR¿QDOORFDWLRQDVSRVVLEOHOHDYLQJ

room for you to make water, drain, electrical and vent

connections to your home.

HOT

COLD

NOTE: If longer drain hose

is required, order drain hose

extension kit, GE part number

WH49X301. Connect additional

drain hose (contained in kit) to

original hose with hose clamp

(contained in kit).

Insert free end of drain hose into

drain opening of your home up

to drain hose stopper (do not

remove hose stopper it prevents

siphoning). If water valves and

drain are built into wall, fasten

drain hose to one of water hoses

with cable tie provided (ribbed

side on inside). If your drains is

a standpipe, fasten drain hose

to standpipe with cable tie

provided.

EXHAUST TO LEFT OR RIGHT SIDE OF

CABINET

• Rotate elbow sections so that the opening points to the

side to which you want to vent. Preassemble 4” elbow

with 4” duct. Use only 4” UL approved rigid metal for

ducting inside the dryer.

• Connect duct assembly to the internal elbow.

WARNING

- Be sure not to pull or damage the

electrical wires inside the dryer when inserting the duct.

• Apply duct tape as shown on the joint between the

dryer internal duct and the straight duct pipe.

WARNING

Internal duct joints must be

secured with tape, otherwise

they may separate and cause

a safety hazard.

• STANDPIPE DIAMETER – The standpipe diameter must

be 1-1/2” minimum. There MUST be an air gap around

WKHGUDLQKRVHLQWKHVWDQGSLSH$VQXJ¿WFDQFDXVHD

siphoning action.

• SIPHON BREAK – For a drain facility less than 33” high,

the hose, coupling and clamps provided in the machine

must be used and, in addition, a siphon break MUST be

installed on the back of the machine. Obtain and use a

siphon break kit and follow the instructions in the kit.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 35 36

Comments to this Manuals

No comments

GE GUD24GSSJWW Instruction Manual Page 10

Comments to this Manuals

Related products and manuals for Electric laundry dryers GE GUD24GSSJWW