GE RAK3202 Installation Manual

Browse online or download Installation Manual for Motorcycle Accessories GE RAK3202. GE RAK3202 Get installation instructions [en] User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
POWER CONNECTION CHART
GE 230/208 Volt Wall Plug Heater Wattage
Power Supply Kit Configuration Circuit Protective Device @ 230/208 Volts
RAK3152 Tandem 15-Amp Time-Delay Fuse or Breaker 2.55/2.09 KW
RAK3202 Perpendicular 20-Amp Time-Delay Fuse or Breaker 3.45/2.82 KW
RAK3302 Large Tandem 30-Amp Time-Delay Fuse or Breaker 5.00/4.10 KW
230/208 VOLT ELECTRICAL SUPPLY
A power supply kit must be used to supply power to the
Zoneline unit. The appropriate kit is determined by the
voltage, the means of electrical connection, and the
amperage of the branch circuit. See the POWER
CONNECTION CHART to confirm the appropriate kit.
All wiring, including installation of the receptacle,
must be in accordance with the NEC and local codes,
ordinances, and regulations.
Installation instructions
RAK3152, RAK3202,
for your new
RAK3302
Power Supply Kit for Cord
or Direct Connection
Before you begin – Read these instructions completely and carefully.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
TOOLS NEEDED
1/4 Nut driver Phillips screwdriver
Wire cutter (For direct connect applications only.)
This kit is for use with 230/208 volt 5200, 5500, and
7500 Series GE Zoneline units only.
IMPORTANT NOTES
This unit must be properly grounded.
The electrical rating marked on the previously installed
Zoneline and power supply kit must be the same as
the supply branch circuit.
Aluminum building wiring may present special
problems—consult a qualified electrician.
All wiring, including installation of the receptacle,
must be in accordance with the NEC and local codes,
ordinances, and regulations.
Use ONLY the wiring size recommended for single
outlet branch circuit.
Proper current protection is the responsibility of
the owner.
Tandem
15 Amp
230/208 volt receptacle configuration
Perpendicular
20 Amp
Large Tandem
30 Amp
Power supply kit
Recommended branch circuit wire sizes*
Nameplate
maximum circuit AWG wire
breaker size size**
15A 14
20A 12
30A 10
AWG – American Wire Gauge
* Single circuit breaker from main box
** Based on copper wire, single-insulated conductor at 60°C
NOTE: Use copper conductors only.
CAUTION:
Disconnect the electrical power
supply before wiring connections.
Page view 0
1 2 3 4

Summary of Contents

Page 1 - RAK3152, RAK3202

POWER CONNECTION CHARTGE 230/208 Volt Wall Plug Heater WattagePower Supply Kit Configuration Circuit Protective Device @ 230/208 VoltsRAK3152 Tandem 1

Page 2 - FOR 7500 SERIES MODELS ONLY

FOR 5200 AND 5500 SERIES MODELS ONLY1. Remove the room cabinet by pulling it out at the bottom to release it (1); then lift it up to clear the rail al

Page 3

FOR 5200 AND 5500 SERIES MODELS ONLY(RAK4002B is also required)1. Remove the room cabinet front from the unit.2. Measure 6″ down the cord from where i

Page 4

FOR 7500 SERIES MODELS ONLY7. Make all wire connections by using appropriate UL-listed electricalconnectors and techniques.8. Select the applicable wi

Comments to this Manuals

No comments