Ge NETWORX NX-548E User Manual download pdf

466-2225B July 2006

NetworX NX-548E Receiver

Installation Instructions

Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Internal mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

External mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DIP switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Testing and troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 6

Programming settings table . . . . . . . . . . . . . . . . . . . . . . . . 7

Supported devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introduction

The NX-548E Receiver adds wireless capabilities to the

NetworX line of control panels. Adding a receiver makes these

control panels compatible with NX wireless transmitters.

Only three wire connections are required for power and commu-

nication to the control panel.

Internal mounting

For internal mounting, mount the receiver inside the control

panel enclosure. Use the following installation guidelines:

• Leave at least 10 in. (25 cm) above the control panel for the

receiver’s antennas.

• Avoid areas that expose the receiver to moisture.

• Avoid areas with excessive metal or electrical wiring,

including furnaces and utility rooms.

To mount the receiver, do the following:

1. Remove the appropriate knockouts on the top of the control

panel enclosure for the antenna shrouds.

2. Assemble the antenna shrouds and fit the black O-rings to

the bottom of each shroud.

3. Insert the shrouds into the knockout holes (Figure 1).

Figure 1. Installing the antenna shrouds

4. Use the mounting screw provided to loosely install the edge

guide standoff in the lower mounting hole in the appropriate

space to the left of the control panel (Figure 2). Do not

tighten the mounting screw down at this time.

Figure 2. Installing the edge guide standoff

5. Slide the printed circuit board into the antennae shroud

slots, after inserting wires into antennae shrouds (Figure 3).

Figure 3. Anntennae shrouds

WARNING: To avoid possible equipment damage

or personal injury, remove power from

the control panel before making any

wiring connections to the receiver.

Antenna shroud

O-ring

Knockout hole

Enclosure top

CAUTION

You must be free of static electricity before

handling circuit boards. Touch a bare metal

surface or wear a grounding strap to

discharge yourself.

Mounting screw

Edge guide standoff

Circuit

Antennae

Enclosure

shrouds

board

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - Installation Instructions

Page 2 - External mounting

NetworX NX-548E ReceiverInstallation Instructions10Zone _____Assigned to module #_____.RM HE P1 - Enable sensor 2 - Supervised 3 - Fire supervis

Page 3 - Power up

11Supported devicesFor 80-bit devices, Feature 6 must be on for Segment 1 on zone location. For 63-bit devices, Feature 6 must be off for Segment 1 on

Page 4 - Programming

NetworX NX-548E ReceiverInstallation Instructions12Specifications FCC compliance This device complies with part 15 of the FCC rules. Operation is subj

Page 5 - Transmitter options

NetworX NX-548E ReceiverInstallation Instructions26. Align the bottom of the circuit board in the edge guide standoff and twist the standoff into plac

Page 6 - Testing and troubleshooting

39. To install the circuit board onto the back plate (Figure 7), insert the antennas into the antenna shrouds, then gently slide the top of the circui

Page 7 - Programming settings table

NetworX NX-548E ReceiverInstallation Instructions4ProgrammingThis section describes how to program the units.Programming guidelinesUse the following p

Page 8

5Transmitter optionsLCD touchpads will display instructions when accomplishing tasks.To program the transmitter and partition settings, do the followi

Page 9

NetworX NX-548E ReceiverInstallation Instructions6Transmitter supervision windowsLCD touchpads will display instructions when accomplishing tasks.To c

Page 10 - NetworX NX-548E Receiver

7Programming settings tableTable 5. Programming settingsLocation Segment 1 Segment 20(Transmitter to program)None NoneZone _____Assigned to module #_

Page 11 - Supported devices

NetworX NX-548E ReceiverInstallation Instructions8Zone _____Assigned to module #_____.RM HE P1 - Enable sensor 2 - Supervised 3 - Fire supervisi

Page 12

9Zone _____Assigned to module #_____.RM HE P1 - Enable sensor 2 - Supervised 3 - Fire supervision 4 - Input option 1 5 - Input option 2 6 - 80-b

Comments to this Manuals

No comments

Ge NETWORX NX-548E User Manual

Browse online or download User Manual for Car radio Ge NETWORX NX-548E. GE NETWORX NX-548E User Manual

Summary of Contents

Comments to this Manuals