Ge 15314 15315 Single Pole Motion Sensing Switch User Manual download pdf

Fig 2

TIME RANGE

LIGHT

Black

Red

Lighting Load

Green (Ground wire to junction box screw or grounding wire)

Motion detected

light

Control cover

removed

Mode selection

switch

Black (Line)

White (Neutral)

Single Pole Motion Sensing Switch

WARNING: For indoor use only. The Single Pole Motion Sensing Switch detects motion to turn on lights

for an adjustable amount of time. A built-in photo cell can be set to keep lights off when the lights

aren't needed. The unit has excellent sensitivity and a wide 150° detection range. It’s intended

to be used with incandescent lighting.

Installation is as easy as replacing a wall switch. However, some

codes require installation by a qualified electrician.

Features include:

• 150° motion detection angle.

• Adjustable on-time from 15 sec to 30 min

• Adjustable room light control.

• Adjustable coverage.

• Works with incandescent lighting.

• Works with motors up to 1/8 hp.

• Slide switch selectable OFF, ON AND AUTO modes.

Included are:

• The sensor switch

• Cover plate

• 3 wire connectors

• 2 large screws

• 2 small screws

INSTALLATION

1. SELECT A LOCATION

New Application

Choose a location where the motion sensor has a clear view of the

entire area where occupant motion may occur.

Retrofit Application

Motion sensing switch will replace existing wall switch. Use only

where the existing switch location provides a clear view of the

occupied area.

General Application Information

The motion sensing switch is more sensitive to motion across the

front of the sensor than to motion towards the sensor. The

detector senses heat in motion and possible heat sources that

change temperature quickly. Therefore, to avoid false triggering,

avoid placing the sensor where it will be aimed at air conditioners,

heaters, laundry equipment and other sources of heat or cold.

2. INSTALLING THE SWITCH

If you are unsure or uncomfortable about

performing this installation, consult a qualified

electrician. WARNING: Turn power off at the

circuit breaker before wiring.

• Remove the decorative cover plate (secured

by two screws).

• Remove Control Cover. (Press in with

screwdriver. Swing out cover to remove.) Fig 1

• Remove the existing switch (if this is a retrofit application).

• Connect the motion sensing switch as shown in Fig 2.

Before installing the motion sensing switch into the box,

make sure there is no bare wire exposed at the

connection.

• Mount the motion sensing switch into the wall box with

the mounting screws

• For test purposes, use a small screwdriver to turn the time control fully counter-clockwise and the

light control fully clockwise. Turn the power back on at the circuit breaker. WARNING: Potential

electrical shock hazard with wall plate removed, do not place fingers or tools into the electrical box.

• Set the switch to the AUTO mode. When unit stabilizes (about 1 minute) the sensor is ready to detect

motion. If motion is detected, the LED indicator light will flash and the lights will turn on. The lights will

turn off 15 seconds after motion is no longer detected.

3. ADJUST TIME, LIGHT LEVEL & RANGE

Time

The length of time that the lights stay on is adjustable from 15

seconds to 30 minutes. Use a small screw driver to set the time by

using the Fig 3 as a guide.

Light Level

The sensor can be prevented from turning on lights when there is

already enough light in the room. Use a small screw driver to set the

light level using this diagram as a guide. In the fully clockwise position (4), the sensor turns on lights

even in full daylight. In the fully counter-clockwise position (1), the sensor only turns on lights when the

surrounding light level is very low.

To adjust the room light control:

1. When the light in the room is at the level you want the lights to turn on, set the switch

to the AUTO position.

2. Set the TIME control to the 15 sec. (fully counter-clockwise) position.

3. Set the LIGHT control to the minimum dark (fully counter-clockwise) position. Wait for

the lights to turn off.

4. Turn the LIGHT adjustment clockwise in very small steps and wait 2 seconds before

moving your hand in front of the sensor. Repeat until the lights controlled by the sensor come on. The

light will now come on when the light level is at or below the present level and motion is detected.

Range

To decrease detection range and sensitivity use a small screw driver and rotate the control counter

clockwise (1). To increase detection range and sensitivity use a small screw driver and rotate the

control clockwise (4). The detection range can be adjusted from 100% to 30%.

NOTE: Do not set the range at maximum level, it may cause the motion sensor to false trigger.

4. FINISH INSTALLATION

Replace control panel cover and install the decorative wall plate. In installations where the motion

sensor switch is combined with other switches or outlets on an expanded box, a combination wall plate

will need to be purchased. Various combination wall plates are available at Home Centers and

Electrical Supply Stores. Slide the switch a couple of times to make sure it operates freely.

5. MODE SELECTION SWITCH

Moving the switch selects one of three modes of operation: OFF, AUTO, ON

• OFF: Lights stay off.

• AUTO: Lights come on for time set when motion is detected and the light level is below the set level.

• ON: Lights stay on continuously.

TROUBLESHOOTING

Light does not come on.

• Circuit breaker or fuse is turned off.

• If the lamp being controlled has another switch, it may be turned off.

• Bulb is defective.

• LIGHT control is set too far toward the DARK position.

• MODE switch is set to OFF instead of AUTO.

• Poor connection.

Lights do not stay on in the Auto mode.

• Motion has stopped in the room.

• TIME control is set for too short a delay.

Light does not turn off.

• Incorrect wiring.

• MODE switch is set to ON instead of AUTO.

• Motion is still present.

• Delay set by TIME control has not expired.

Light comes on for no reason in the Auto mode.

• Heating or cooling objects (such as air vents, appliances, or drafts through the wall box) are causing

false triggering.

• Switch on the sensor has been turned off and back on.

• There was a momentary power interruption. The light will turn off automatically when the "on" time

expires.

SPECIFICATIONS

Electrical input: 120V, 60 Hz

Motor Load: 1/8 HP maximum

Incandescent: 500W maximum

On-Time: Adjustable approximately 15 sec. to 30 min.

Photocell Sensor: From full daylight to less than 1 FC.

Coverage: up to 15 ft. at 150°, up to 40 ft. in front of the sensor

Questions? Visit us at www.jascoproducts.com

Typical coverage

OFF

Fig 1

Fig 3

TEST = 15 seconds

TIME RANGE

LIGHT

Control panel

15314

15315

57884

57885

6/26/2012

Version01

1 2

TIME RANGE 1

Summary of Contents

Page 1 - TIME RANGE

Fig 2TIME RANGELIGHTBlackRedLighting LoadGreen (Ground wire to junction box screw or grounding wire)Motion detectedlightControl coverremovedMode sele

Page 2

Fig 2TIME RANGELIGHTNegroRojoCarga de IluminaciónVerde (Cable a tierra al tornillo de la caja deempalmes o el cable de tierra)Movimiento luzdetectado

Comments to this Manuals

No comments

Ge 15314 15315 Single Pole Motion Sensing Switch User Manual

Browse online or download User Manual for Accessories for electrical Ge 15314 15315 Single Pole Motion Sensing Switch. GE 15314 15315 Single Pole Motion Sensing Switch User Manual [en] [de] [es] [fr] [it]

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for electrical Ge 15314 15315 Single Pole Motion Sensing Switch